Hi Geert.
> Thanks for your comments!
>
> > On Thu, Jan 02, 2020 at 03:12:46PM +0100, Geert Uytterhoeven wrote:
> > > Add support for the Okaya RH128128T display to the st7735r driver.
> > >
> > > The RH128128T is a 128x128 1.44" TFT display driven by a Sitronix
> > > ST7715R TFT Controller/Driver. The latter is very similar to the
> > > ST7735R, and can be handled by the existing st7735r driver.
> >
> > As a general comment - it would have eased review if this was split
> > in two patches.
> > One patch to introduce the infrastructure to deal with another set of
> > controller/display and one patch introducing the new combination.
>
> I had thought about that, but didn't pursue as the new combination is
> just 7 added lines. If you prefer a split, I can do that.
The good thing with a split is that is shows how little is really
required to support a new controller/panel pair.
So it would be good if you did so.
>
> > > --- a/drivers/gpu/drm/tiny/st7735r.c
> > > +++ b/drivers/gpu/drm/tiny/st7735r.c
> > > @@ -1,8 +1,9 @@
> > > // SPDX-License-Identifier: GPL-2.0+
> > > /*
> > > - * DRM driver for Sitronix ST7735R panels
> > > + * DRM driver for Sitronix ST7715R/ST7735R panels
> >
> > This comment could describe the situation a little better.
> > This is a sitronix st7735r controller with a jianda jd-t18003-t01
> > display.
> > Or a sitronix st7715r controller with a okaya rh128128t display.
>
> Indeed. It is currently limited to two controller/display combos.
> But I expect more combos to be added over time.
> Hence does it make sense to describe all of that in the top comments?
If we do describe it we should do so as kernel-doc and then wire up the
driver somwhere under Documentation/gpu/
But there is no good place to wire it up yet.
> > > @@ -37,12 +39,28 @@
> > > #define ST7735R_MY BIT(7)
> > > #define ST7735R_MX BIT(6)
> > > #define ST7735R_MV BIT(5)
> > > +#define ST7735R_RGB BIT(3)
> > > +
> > > +struct st7735r_cfg {
> > > + const struct drm_display_mode mode;
> > > + unsigned int left_offset;
> > > + unsigned int top_offset;
> > > + unsigned int write_only:1;
> > > + unsigned int rgb:1; /* RGB (vs. BGR) */
> > > +};
> > > +
> > > +struct st7735r_priv {
> > > + struct mipi_dbi_dev dbidev; /* Must be first for .release() */
> > > + unsigned int rgb:1;
> > > +};
> >
> > The structs here uses "st7735r" as the generic prefix.
> > But the rest of this file uses "jd_t18003_t01" as the generic prefix.
> >
> > It would help readability if the same prefix is used for the common
> > stuff everywhere.
>
> Agreed.
> So I think it makes most sense to rename jd_t18003_t01_pipe_{enable,funcs}
> to sh7735r_pipe_{enable,funcs}?
s/sh/st/
Yeah, or maybe just sitronix_pipe_{enable,funcs} as we have support
for more than one Sitronix controller anyway.
> If needed, the display-specific parts (e.g. gamma parameters) could be
> factored out in st7735r_cfg later, if neeeded.
>
> In reality, there are lots of different ways to communicate with an
> ST77[13]5R display controller (3/4-wire SPI, or 6800/8080 bus, ...), and
> lots of different ways to wire a display to the controller. Ideally,
> this should be described in DT. As I don't have schematics for the
> display board, doing so is difficult, and will miss important details,
> which may lead to DTB ABI compatibility issues later.
> I understand using these compatible combinations was a pragmatic solution
> to this problem.
Agreed, let's bite that when we have a display we care enough about
and maybe then we also can write a proper driver for it.
I have a few displays here using 8080 and I hope someone steps up
to do proper support for such displays.
> > >
> > > static const struct spi_device_id st7735r_id[] = {
> > > - { "jd-t18003-t01", 0 },
> > > + { "jd-t18003-t01", (uintptr_t)&jd_t18003_t01_cfg },
> > > { },
> > { /* sentinel */ },
> >
> > Do we need an entry for "okaya,rh128128t" here?
> >
> > Note: I have not fully understood how MODULE_DEVICE_TABLE()
> > works - so forgive me my ignorance.
>
> st7735r_id[] is used for matching based on platform device name.
> Hence an entry is needed only to use the display on non-DT systems.
> Can be added later, if ever needed.
>
> Note that there is a separate MODULE_DEVICE_TABLE() for DT-based matching,
> so the driver module will be auto-loaded on DT-based systems.
Thanks for the explanation.
Sam
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
