On Mon, Dec 2, 2019 at 6:48 AM Chandan Uddaraju <chandanu@xxxxxxxxxxxxxx> wrote:
>
> Add bindings for Snapdragon 845 DisplayPort and
> display-port PLL driver.
>
> Changes in V2:
> Provide details about sel-gpio
>
> Signed-off-by: Chandan Uddaraju <chandanu@xxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/display/msm/dp.txt | 249 +++++++++++++++++++++
> .../devicetree/bindings/display/msm/dpu.txt | 16 +-
> 2 files changed, 261 insertions(+), 4 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/display/msm/dp.txt
>
> diff --git a/Documentation/devicetree/bindings/display/msm/dp.txt b/Documentation/devicetree/bindings/display/msm/dp.txt
> new file mode 100644
> index 0000000..38be36d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/msm/dp.txt
> @@ -0,0 +1,249 @@
> +Qualcomm Technologies, Inc.
> +DP is the master Display Port device which supports DP host controllers that are compatible with VESA Display Port interface specification.
> +DP Controller: Required properties:
> +- compatible: Should be "qcom,dp-display".
> +- reg: Base address and length of DP hardware's memory mapped regions.
> +- cell-index: Specifies the controller instance.
> +- reg-names: A list of strings that name the list of regs.
> + "dp_ahb" - DP controller memory region.
> + "dp_aux" - DP AUX memory region.
> + "dp_link" - DP link layer memory region.
> + "dp_p0" - DP pixel clock domain memory region.
> + "dp_phy" - DP PHY memory region.
> + "dp_ln_tx0" - USB3 DP PHY combo TX-0 lane memory region.
> + "dp_ln_tx1" - USB3 DP PHY combo TX-1 lane memory region.
> + "dp_mmss_cc" - Display Clock Control memory region.
> + "qfprom_physical" - QFPROM Phys memory region.
> + "dp_pll" - USB3 DP combo PLL memory region.
> + "usb3_dp_com" - USB3 DP PHY combo memory region.
> + "hdcp_physical" - DP HDCP memory region.
> +- interrupt-parent phandle to the interrupt parent device node.
> +- interrupts: The interrupt signal from the DP block.
> +- clocks: Clocks required for Display Port operation. See [1] for details on clock bindings.
> +- clock-names: Names of the clocks corresponding to handles. Following clocks are required:
> + "core_aux_clk", "core_usb_ref_clk_src","core_usb_ref_clk", "core_usb_cfg_ahb_clk",
> + "core_usb_pipe_clk", "ctrl_link_clk", "ctrl_link_iface_clk", "ctrl_crypto_clk",
> + "ctrl_pixel_clk", "pixel_clk_rcg", "pixel_parent".
> +- pll-node: phandle to DP PLL node.
> +- vdda-1p2-supply: phandle to vdda 1.2V regulator node.
> +- vdda-0p9-supply: phandle to vdda 0.9V regulator node.
> +- qcom,aux-cfg0-settings: Specifies the DP AUX configuration 0 settings. The first
> + entry in this array corresponds to the register offset
> + within DP AUX, while the remaining entries indicate the
> + programmable values.
> +- qcom,aux-cfg1-settings: Specifies the DP AUX configuration 1 settings. The first
> + entry in this array corresponds to the register offset
> + within DP AUX, while the remaining entries indicate the
> + programmable values.
> +- qcom,aux-cfg2-settings: Specifies the DP AUX configuration 2 settings. The first
> + entry in this array corresponds to the register offset
> + within DP AUX, while the remaining entries indicate the
> + programmable values.
> +- qcom,aux-cfg3-settings: Specifies the DP AUX configuration 3 settings. The first
> + entry in this array corresponds to the register offset
> + within DP AUX, while the remaining entries indicate the
> + programmable values.
> +- qcom,aux-cfg4-settings: Specifies the DP AUX configuration 4 settings. The first
> + entry in this array corresponds to the register offset
> + within DP AUX, while the remaining entries indicate the
> + programmable values.
> +- qcom,aux-cfg5-settings: Specifies the DP AUX configuration 5 settings. The first
> + entry in this array corresponds to the register offset
> + within DP AUX, while the remaining entries indicate the
> + programmable values.
> +- qcom,aux-cfg6-settings: Specifies the DP AUX configuration 6 settings. The first
> + entry in this array corresponds to the register offset
> + within DP AUX, while the remaining entries indicate the
> + programmable values.
> +- qcom,aux-cfg7-settings: Specifies the DP AUX configuration 7 settings. The first
> + entry in this array corresponds to the register offset
> + within DP AUX, while the remaining entries indicate the
> + programmable values.
> +- qcom,aux-cfg8-settings: Specifies the DP AUX configuration 8 settings. The first
> + entry in this array corresponds to the register offset
> + within DP AUX, while the remaining entries indicate the
> + programmable values.
> +- qcom,aux-cfg9-settings: Specifies the DP AUX configuration 9 settings. The first
> + entry in this array corresponds to the register offset
> + within DP AUX, while the remaining entries indicate the
> + programmable values.
> +- qcom,max-pclk-frequency-khz: An integer specifying the maximum. pixel clock in KHz supported by Display Port.
> +- extcon: Phandle for the external connector class interface.
> +- qcom,<type>-supply-entries: A node that lists the elements of the supply used by the a particular "type" of DP module. The module "types"
> + can be "core", "ctrl", and "phy". Within the same type,
> + there can be more than one instance of this binding,
> + in which case the entry would be appended with the
> + supply entry index.
> + e.g. qcom,ctrl-supply-entry@0
> + -- qcom,supply-name: name of the supply (vdd/vdda/vddio)
> + -- qcom,supply-min-voltage: minimum voltage level (uV)
> + -- qcom,supply-max-voltage: maximum voltage level (uV)
> + -- qcom,supply-enable-load: load drawn (uA) from enabled supply
> + -- qcom,supply-disable-load: load drawn (uA) from disabled supply
> + -- qcom,supply-pre-on-sleep: time to sleep (ms) before turning on
> + -- qcom,supply-post-on-sleep: time to sleep (ms) after turning on
> + -- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off
> + -- qcom,supply-post-off-sleep: time to sleep (ms) after turning off
> +- pinctrl-names: List of names to assign mdss pin states defined in pinctrl device node
> + Refer to pinctrl-bindings.txt
> +- pinctrl-<0..n>: Lists phandles each pointing to the pin configuration node within a pin
> + controller. These pin configurations are installed in the pinctrl
> + device node. Refer to pinctrl-bindings.txt
> +DP Endpoint properties:
> + - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's
> + input endpoint. For port@1, set to the DPU interface output. See [2] for
> + device graph info.
> +
> +Optional properties:
> +- qcom,aux-en-gpio: Specifies the aux-channel enable gpio.
> +- qcom,aux-sel-gpio: Specifies the mux-selection that might be needed for aux interface.
> +
> +
> +DP PLL: Required properties:
> +- compatible: Should be "qcom,dp-pll-10nm".
> +- reg: Base address and length of DP hardware's memory mapped regions.
> +- cell-index: Specifies the PLL instance.
> +- reg-names: A list of strings that name the list of regs.
> + "pll_base" - DP PLL memory region.
> + "phy_base" - DP PHY memory region.
> + "ln_tx0_base" - USB3 DP PHY combo TX-0 lane memory region.
> + "ln_tx1_base" - USB3 DP PHY combo TX-1 lane memory region.
> + "gdsc_base" - gdsc memory region.
> +- interrupt-parent phandle to the interrupt parent device node.
> +- interrupts: The interrupt signal from the DP block.
> +- clocks: Clocks required for Display Port operation. See [1] for details on clock bindings.
> +- clock-names: Names of the clocks corresponding to handles. Following clocks are required:
> + "iface_clk", "ref_clk", cfg_ahb_clk", "pipe_clk".
> +- clock-rate: Initial clock rate to be configured. For the shared clocks, the default value is set to zero so that minimum clock value is configured. Non-zero clock
> + value can be used to configure DP pixel clock.
This should be a clock provider, no?
> +
> +
> +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
> +[2] Documentation/devicetree/bindings/graph.txt
> +
> +Example:
> + msm_dp: dp_display@ae90000{
> + cell-index = <0>;
> + compatible = "qcom,dp-display";
> +
> + reg = <0 0x90000 0x0dc>,
> + <0 0x90200 0x0c0>,
> + <0 0x90400 0x508>,
> + <0 0x90a00 0x094>,
> + <1 0xeaa00 0x200>,
> + <1 0xea200 0x200>,
> + <1 0xea600 0x200>,
> + <2 0x02000 0x1a0>,
> + <3 0x00000 0x621c>,
> + <1 0xea000 0x180>,
> + <1 0xe8000 0x20>,
> + <4 0xe1000 0x034>;
> + reg-names = "dp_ahb", "dp_aux", "dp_link",
> + "dp_p0", "dp_phy", "dp_ln_tx0", "dp_ln_tx1",
> + "dp_mmss_cc", "qfprom_physical", "dp_pll",
> + "usb3_dp_com", "hdcp_physical";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <12 0>;
> +
> + extcon = <&usb_1_ssphy>;
> + clocks = <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
> + <&rpmhcc RPMH_CXO_CLK>,
> + <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
> + <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
> + <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>,
> + <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
> + <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
> + <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>,
> + <&dispcc DISP_CC_MDSS_DP_CRYPTO_CLK>,
> + <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
> + clock-names = "core_aux_clk", "core_ref_clk_src",
> + "core_usb_ref_clk", "core_usb_cfg_ahb_clk",
> + "core_usb_pipe_clk", "ctrl_link_clk",
> + "ctrl_link_iface_clk", "ctrl_pixel_clk",
> + "crypto_clk", "pixel_clk_rcg";
> +
> + pll-node = <&dp_pll>;
> + qcom,aux-cfg0-settings = [20 00];
> + qcom,aux-cfg1-settings = [24 13 23 1d];
> + qcom,aux-cfg2-settings = [28 24];
> + qcom,aux-cfg3-settings = [2c 00];
> + qcom,aux-cfg4-settings = [30 0a];
> + qcom,aux-cfg5-settings = [34 26];
> + qcom,aux-cfg6-settings = [38 0a];
> + qcom,aux-cfg7-settings = [3c 03];
> + qcom,aux-cfg8-settings = [40 bb];
> + qcom,aux-cfg9-settings = [44 03];
> +
> + qcom,max-pclk-frequency-khz = <675000>;
> +
> + qcom,ctrl-supply-entries {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + qcom,ctrl-supply-entry@0 {
> + reg = <0>;
> + qcom,supply-name = "vdda-1p2";
> + qcom,supply-min-voltage = <1200000>;
> + qcom,supply-max-voltage = <1200000>;
> + qcom,supply-enable-load = <21800>;
> + qcom,supply-disable-load = <4>;
> + };
> + };
> +
> + qcom,phy-supply-entries {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + qcom,phy-supply-entry@0 {
> + reg = <0>;
> + qcom,supply-name = "vdda-0p9";
> + qcom,supply-min-voltage = <880000>;
> + qcom,supply-max-voltage = <880000>;
> + qcom,supply-enable-load = <36000>;
> + qcom,supply-disable-load = <32>;
> + };
> + };
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + dp_in: endpoint {
> + remote-endpoint = <&dpu_intf0_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + dp_out: endpoint {
> + };
> + };
> + };
> + };
> +
> + dp_pll: dp-pll@c011000 {
> + compatible = "qcom,dp-pll-10nm";
> + label = "DP PLL";
> + cell-index = <0>;
> + #clock-cells = <1>;
> +
> + reg = <1 0xea000 0x200>,
> + <1 0xeaa00 0x200>,
> + <1 0xea200 0x200>,
> + <1 0xea600 0x200>,
> + <2 0x03000 0x8>;
> + reg-names = "pll_base", "phy_base", "ln_tx0_base",
> + "ln_tx1_base", "gdsc_base";
> +
> + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> + <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
> + <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
> + <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
> + clock-names = "iface_clk", "ref_clk",
> + "cfg_ahb_clk", "pipe_clk";
> + clock-rate = <0>;
> +
> + };
> diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt
> index a61dd40..eac6e1c 100644
> --- a/Documentation/devicetree/bindings/display/msm/dpu.txt
> +++ b/Documentation/devicetree/bindings/display/msm/dpu.txt
> @@ -63,8 +63,9 @@ Required properties:
> Documentation/devicetree/bindings/graph.txt
> Documentation/devicetree/bindings/media/video-interfaces.txt
>
> - Port 0 -> DPU_INTF1 (DSI1)
> - Port 1 -> DPU_INTF2 (DSI2)
> + Port 0 -> DPU_INTF0 (DP)
> + Port 1 -> DPU_INTF1 (DSI1)
> + Port 2 -> DPU_INTF2 (DSI2)
>
> Optional properties:
> - assigned-clocks: list of clock specifiers for clocks needing rate assignment
> @@ -125,13 +126,20 @@ Example:
>
> port@0 {
> reg = <0>;
> - dpu_intf1_out: endpoint {
> - remote-endpoint = <&dsi0_in>;
> + dpu_intf0_out: endpoint {
> + remote-endpoint = <&dp_in>;
> };
> };
>
> port@1 {
> reg = <1>;
> + dpu_intf1_out: endpoint {
> + remote-endpoint = <&dsi0_in>;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> dpu_intf2_out: endpoint {
> remote-endpoint = <&dsi1_in>;
> };
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project
>
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
