On 12/4/19 10:35 AM, Thomas Zimmermann wrote: > Hi > > Am 19.11.19 um 14:47 schrieb Benjamin Gaignard: >> When compiling with W=1 few warnings about unused variables show up. >> This patch removes all the involved variables. >> >> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@xxxxxx> >> --- >> drivers/gpu/drm/drm_modes.c | 22 +++------------------- >> 1 file changed, 3 insertions(+), 19 deletions(-) >> >> diff --git a/drivers/gpu/drm/drm_modes.c b/drivers/gpu/drm/drm_modes.c >> index 88232698d7a0..aca901aff042 100644 >> --- a/drivers/gpu/drm/drm_modes.c >> +++ b/drivers/gpu/drm/drm_modes.c >> @@ -233,7 +233,7 @@ struct drm_display_mode *drm_cvt_mode(struct drm_device *dev, int hdisplay, >> /* 3) Nominal HSync width (% of line period) - default 8 */ >> #define CVT_HSYNC_PERCENTAGE 8 >> unsigned int hblank_percentage; >> - int vsyncandback_porch, vback_porch, hblank; >> + int vsyncandback_porch, hblank; >> >> /* estimated the horizontal period */ >> tmp1 = HV_FACTOR * 1000000 - >> @@ -249,7 +249,6 @@ struct drm_display_mode *drm_cvt_mode(struct drm_device *dev, int hdisplay, >> else >> vsyncandback_porch = tmp1; >> /* 10. Find number of lines in back porch */ >> - vback_porch = vsyncandback_porch - vsync; >> drm_mode->vtotal = vdisplay_rnd + 2 * vmargin + >> vsyncandback_porch + CVT_MIN_V_PORCH; >> /* 5) Definition of Horizontal blanking time limitation */ >> @@ -386,9 +385,8 @@ drm_gtf_mode_complex(struct drm_device *dev, int hdisplay, int vdisplay, >> int top_margin, bottom_margin; >> int interlace; >> unsigned int hfreq_est; >> - int vsync_plus_bp, vback_porch; >> - unsigned int vtotal_lines, vfieldrate_est, hperiod; >> - unsigned int vfield_rate, vframe_rate; >> + int vsync_plus_bp; >> + unsigned int vtotal_lines; >> int left_margin, right_margin; >> unsigned int total_active_pixels, ideal_duty_cycle; >> unsigned int hblank, total_pixels, pixel_freq; >> @@ -451,23 +449,9 @@ drm_gtf_mode_complex(struct drm_device *dev, int hdisplay, int vdisplay, >> /* [V SYNC+BP] = RINT(([MIN VSYNC+BP] * hfreq_est / 1000000)) */ >> vsync_plus_bp = MIN_VSYNC_PLUS_BP * hfreq_est / 1000; >> vsync_plus_bp = (vsync_plus_bp + 500) / 1000; >> - /* 9. Find the number of lines in V back porch alone: */ >> - vback_porch = vsync_plus_bp - V_SYNC_RQD; >> /* 10. Find the total number of lines in Vertical field period: */ >> vtotal_lines = vdisplay_rnd + top_margin + bottom_margin + >> vsync_plus_bp + GTF_MIN_V_PORCH; >> - /* 11. Estimate the Vertical field frequency: */ >> - vfieldrate_est = hfreq_est / vtotal_lines; >> - /* 12. Find the actual horizontal period: */ >> - hperiod = 1000000 / (vfieldrate_rqd * vtotal_lines); >> - >> - /* 13. Find the actual Vertical field frequency: */ >> - vfield_rate = hfreq_est / vtotal_lines; >> - /* 14. Find the Vertical frame frequency: */ >> - if (interlaced) >> - vframe_rate = vfield_rate / 2; >> - else >> - vframe_rate = vfield_rate; > The amount of unused code is quite large, which makes me wonder if > there's something missing below where these variables are supposed to be > used. > > If these variables can be removed, comments should mention that steps 9 > and 11 to 14 are being left out. After all, the function is fairly > explicit about implementing the GTF algorithm step by step. > > Best regards > Thomas If the goal is to keep all the steps then I could prefix all problematic variables with __maybe_unused macro. Benjamin > >> /* 15. Find number of pixels in left margin: */ >> if (margins) >> left_margin = (hdisplay_rnd * GTF_MARGIN_PERCENTAGE + 500) / >> _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
