Hi Adam, On Mon, Dec 02, 2019 at 07:24:09AM -0600, Adam Ford wrote: > On Mon, Dec 2, 2019 at 7:13 AM Laurent Pinchart wrote: > > On Thu, Nov 14, 2019 at 11:39:47AM +0200, Tomi Valkeinen wrote: > > > Hi Tony, Thierry, Laurent, > > > > > > After the recent change of moving from omapdrm specific panel-dpi driver > > > to the DRM simple panel, AM4 EVM/ePOS's panel is not working quite > > > right. This series has fixes for it, but I'm not sure if these are the > > > right ways to fix the issues, so comments welcome. > > > > > > 1) Panel driver is not probed. With omapdrm's panel-dpi, the match > > > happened with "panel-dpi" compatible string. Now with panel-simple, the > > > match should happen with the panel model compatible string, which is > > > "osddisplays,osd057T0559-34ts" in the DT file. However, no such > > > compatible exists in panel-simple. > > > > I've also noticed that we have a few other omap-based platforms that > > got broken, for the same reason :-( We're missing driver support for > > innolux,at070tn83, samsung,lte430wq-f0c and startek,startek-kd050c, and > > we have a few nodes that use panel-dpi without any more precise > > compatible string. > > > > > Interestingly, the actual panel at least on my EVMs and ePOSes is not > > > osd057T0559-34ts, but osd070t1718-19ts. Also, I was unable to find any > > > information about osd057T0559-34ts. I don't know the history with this, > > > so it is possible that the early versions of the boards did have > > > osd057T0559-34ts, but was later changed to osd070t1718-19ts. > > > > > > As osd070t1718-19ts is supported by panel-simple, changing the > > > compatible string to osd070t1718-19ts in the DT file solves this one. > > > > > > 2) Timings in DT file cause a kernel warning. Omapdrm's panel-dpi used > > > video timings from the DT file, so they are present in all the DT files. > > > panel-simple uses timings from a table in the panel-simple driver, but > > > gives a kernel warning if the DT file contains timings. > > > > > > This can be solved by removing the timings from the DT file. > > > > > > 3) Sync drive edge is not right. This one might have been present also > > > with panel-dpi, I didn't verify. The problem is that the panel-simple > > > data for osddisplays_osd070t1718_19ts defines bus_flags for DE polarity > > > and pixdata edge, but not for sync edge. > > > > > > The datasheet for the panel does not give any hint on what the edge > > > should be. Omapdrm defaults to driving syncs on falling edge, which > > > caused the image to be shifted one pixel to the right. > > > > > > Adding DRM_BUS_FLAG_SYNC_DRIVE_POSEDGE bus_flag solves the problem. AM5 > > > EVM also has the same panel with the same behavior. > > > > > > ==== > > > > > > The reason I'm not sure if the 1) and 2) fixes are correct is that > > > they're breaking DT compatibility. Should we instead make changes to > > > panel-simple to keep the same DT files working? > > > > That's tempting, as breaking DT is quite bad, but that would require > > adding a match on panel-dpi, and parsing timings in the panel-simple > > driver. Thierry has always been opposed to that as far as I can tell, > > and even if I don't share his point of view, I don't want to move in > > this direction without a consensus. > > What about a generic driver separate from the simple panel driver that > does just the panel-dpi parsing? A separate driver wouldn't make too much of a difference. Thierry's point was that drivers should hardcode the timings, as the compatible string gives enough information and encoding timings in DT would duplicate that information. I have a different point of view, and there are pros and cons for both options, so we haven't been able to reach an agreement. That's why I haven't pushed too hard for timings parsing from DT, regardless of whether it would be in panel-simple or in a separate driver. > If we exported the necessary functions from simple-panel, we could > call them from the panel-dpi parser and not have to re-invent the > functions to enable power, gpio or back light and/or fix them each > time they get updated. > > > Your series is fine in my opinion, as even if we decide to handle > > backward compatibility in this case, changing the DT files in mainline > > is still the right way to go (if only to avoid giving wrong examples). > > > > > This would mean adding a new entry for the osd057T0559-34ts panel, but > > > as we don't have datasheet for it, I think we could just append the > > > compatible string to osd070t1718-19t's data. > > > > > > It would also mean doing some change to the panel-simple code that gives > > > the warning about timings in DT data. This might make sense, as I think > > > we have other DT files with video timings too. > > > > > > For 3), I think the patch is fine, but I'm not sure if the display > > > controller driver should be able to deduce the sync drive edge from the > > > pixdata drive edge. Are they usually the same? I have no idea... > > > > > > Tomi Valkeinen (3): > > > ARM: dts: am437x-gp/epos-evm: fix panel compatible > > > ARM: dts: am437x-gp/epos-evm: drop unused panel timings > > > drm/panel: simple: fix osd070t1718_19ts sync drive edge > > > > > > arch/arm/boot/dts/am437x-gp-evm.dts | 18 +----------------- > > > arch/arm/boot/dts/am43x-epos-evm.dts | 18 +----------------- > > > drivers/gpu/drm/panel/panel-simple.c | 3 ++- > > > 3 files changed, 4 insertions(+), 35 deletions(-) -- Regards, Laurent Pinchart _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
