On Thu, Nov 21, 2019 at 04:43:24PM +0100, Rafael J. Wysocki wrote:
> On Thu, Nov 21, 2019 at 1:52 PM Mika Westerberg
> <mika.westerberg@xxxxxxxxx> wrote:
> >
> > On Thu, Nov 21, 2019 at 01:46:14PM +0200, Mika Westerberg wrote:
> > > On Thu, Nov 21, 2019 at 12:34:22PM +0100, Rafael J. Wysocki wrote:
> > > > On Thu, Nov 21, 2019 at 12:28 PM Mika Westerberg
> > > > <mika.westerberg@xxxxxxxxx> wrote:
> > > > >
> > > > > On Wed, Nov 20, 2019 at 11:29:33PM +0100, Rafael J. Wysocki wrote:
> > > > > > > last week or so I found systems where the GPU was under the "PCI
> > > > > > > Express Root Port" (name from lspci) and on those systems all of that
> > > > > > > seems to work. So I am wondering if it's indeed just the 0x1901 one,
> > > > > > > which also explains Mikas case that Thunderbolt stuff works as devices
> > > > > > > never get populated under this particular bridge controller, but under
> > > > > > > those "Root Port"s
> > > > > >
> > > > > > It always is a PCIe port, but its location within the SoC may matter.
> > > > >
> > > > > Exactly. Intel hardware has PCIe ports on CPU side (these are called
> > > > > PEG, PCI Express Graphics, ports), and the PCH side. I think the IP is
> > > > > still the same.
> > > > >
> > > > > > Also some custom AML-based power management is involved and that may
> > > > > > be making specific assumptions on the configuration of the SoC and the
> > > > > > GPU at the time of its invocation which unfortunately are not known to
> > > > > > us.
> > > > > >
> > > > > > However, it looks like the AML invoked to power down the GPU from
> > > > > > acpi_pci_set_power_state() gets confused if it is not in PCI D0 at
> > > > > > that point, so it looks like that AML tries to access device memory on
> > > > > > the GPU (beyond the PCI config space) or similar which is not
> > > > > > accessible in PCI power states below D0.
> > > > >
> > > > > Or the PCI config space of the GPU when the parent root port is in D3hot
> > > > > (as it is the case here). Also then the GPU config space is not
> > > > > accessible.
> > > >
> > > > Why would the parent port be in D3hot at that point? Wouldn't that be
> > > > a suspend ordering violation?
> > >
> > > No. We put the GPU into D3hot first,
>
> OK
>
> Does this involve any AML, like a _PS3 under the GPU object?
I don't see _PS3 (nor _PS0) for that object. If I read it right the GPU
itself is not described in ACPI tables at all.
> > > then the root port and then turn
> > > off the power resource (which is attached to the root port) resulting
> > > the topology entering D3cold.
> >
> > I don't see that happening in the AML though.
>
> Which AML do you mean, specifically? The _OFF method for the root
> port's _PR3 power resource or something else?
The root port's _OFF method for the power resource returned by its _PR3.
> > Basically the difference is that when Windows 7 or Linux (the _REV==5
> > check) then we directly do link disable whereas in Windows 8+ we invoke
> > LKDS() method that puts the link into L2/L3. None of the fields they
> > access seem to touch the GPU itself.
>
> So that may be where the problem is.
>
> Putting the downstream component into PCI D[1-3] is expected to put
> the link into L1, so I'm not sure how that plays with the later
> attempt to put it into L2/L3 Ready.
That should be fine. What I've seen the link goes into L1 when
downstream component is put to D-state (not D0) and then it is put back
to L0 when L2/3 ready is propagated. Eventually it goes into L2 or L3.
> Also, L2/L3 Ready is expected to be transient, so finally power should
> be removed somehow.
There is GPIO for both power and PERST, I think the line here:
\_SB.SGOV (0x01010004, Zero)
is the one that removes power.
> > LKDS() for the first PEG port looks like this:
> >
> > P0L2 = One
> > Sleep (0x10)
> > Local0 = Zero
> > While (P0L2)
> > {
> > If ((Local0 > 0x04))
> > {
> > Break
> > }
> >
> > Sleep (0x10)
> > Local0++
> > }
> >
> > One thing that comes to mind is that the loop can end even if P0L2 is
> > not cleared as it does only 5 iterations with 16 ms sleep between. Maybe
> > Sleep() is implemented differently in Windows? I mean Linux may be
> > "faster" here and return prematurely and if we leave the port into D0
> > this does not happen, or something. I'm just throwing out ideas :)
>
> But this actually works for the downstream component in D0, doesn't it?
It does and that leaves the link in L0 so it could be that then the
above AML works better or something.
That reminds me, ASPM may have something to do with this as well.
> Also, if the downstream component is in D0, the port actually should
> stay in D0 too, so what would happen with the $subject patch applied?
Parent port cannot be lower D-state than the child so I agree it should
stay in D0 as well. However, it seems that what happens is that the
issue goes away :)
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
