Hi Laurent,
Thank you for your feedback!
> From: linux-renesas-soc-owner@xxxxxxxxxxxxxxx <linux-renesas-soc-owner@xxxxxxxxxxxxxxx> On Behalf Of Laurent Pinchart
> Sent: 07 November 2019 20:55
> Subject: Re: [PATCH v3 6/7] ARM: dts: iwg20d-q7-common: Add LCD support
>
> Hi Fabrizio,
>
> Thank you for the patch.
>
> On Thu, Nov 07, 2019 at 08:11:02PM +0000, Fabrizio Castro wrote:
> > The iwg20d comes with a 7" capacitive touch screen, therefore
> > add support for it.
> >
> > Signed-off-by: Fabrizio Castro <fabrizio.castro@xxxxxxxxxxxxxx>
> >
> > ---
> > v2->v3:
> > * No change
> > v1->v2:
> > * No change
> > ---
> > arch/arm/boot/dts/iwg20d-q7-common.dtsi | 85 ++++++++++++++++++++++++++++++++
> > arch/arm/boot/dts/iwg20d-q7-dbcm-ca.dtsi | 1 -
> > 2 files changed, 85 insertions(+), 1 deletion(-)
> >
> > diff --git a/arch/arm/boot/dts/iwg20d-q7-common.dtsi b/arch/arm/boot/dts/iwg20d-q7-common.dtsi
> > index ae75a1db..3428b8d 100644
> > --- a/arch/arm/boot/dts/iwg20d-q7-common.dtsi
> > +++ b/arch/arm/boot/dts/iwg20d-q7-common.dtsi
> > @@ -46,6 +46,49 @@
> > clock-frequency = <26000000>;
> > };
> >
> > + lcd_backlight: backlight {
> > + compatible = "pwm-backlight";
> > +
> > + pwms = <&pwm3 0 5000000 0>;
> > + brightness-levels = <0 4 8 16 32 64 128 255>;
> > + default-brightness-level = <7>;
> > + enable-gpios = <&gpio5 14 GPIO_ACTIVE_HIGH>;
> > + };
> > +
> > + lvds-receiver {
> > + compatible = "lvds-decoder";
>
> A specific compatible string is required.
Will document the specific compatible in the binding doc
>
> I think the lvds-decoder driver should error out at probe time if only
> one compatible string is listed.
Ok, will modify the driver accordingly
>
> > + powerdown = <&gpio7 25 GPIO_ACTIVE_LOW>;
>
> powerdown-gpios ?
That's a bug, well spotted.
>
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > + lvds_receiver_in: endpoint {
> > + remote-endpoint = <&lvds0_out>;
> > + };
> > + };
> > + port@1 {
> > + reg = <1>;
> > + lvds_receiver_out: endpoint {
> > + remote-endpoint = <&panel_in>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + panel {
> > + compatible = "edt,etm0700g0dh6", "simple-panel";
>
> There's no "simple-panel" compatible string defined anywhere as far as I
> can tell.
The usage of "simple-panel" as a compatible is widespread and really confusing.
The fact that you made this comment is good enough for me to say we don't
need it, I'll take it out.
>
> > + backlight = <&lcd_backlight>;
> > +
> > + port {
> > + panel_in: endpoint {
> > + remote-endpoint = <&lvds_receiver_out>;
> > + };
> > + };
> > + };
> > +
> > reg_1p5v: 1p5v {
> > compatible = "regulator-fixed";
> > regulator-name = "1P5V";
> > @@ -120,6 +163,18 @@
> > status = "okay";
> > };
> >
> > +&du {
> > + status = "okay";
> > +};
> > +
> > +&gpio2 {
> > + touch-interrupt {
> > + gpio-hog;
> > + gpios = <12 GPIO_ACTIVE_LOW>;
> > + input;
> > + };
>
> Do you need this, with the touchpanel@38 node already listing the
> interrupt ?
Yes, unfortunately we do need this as the bootloader is poking with the gpio.
I can't fix this in the bootloader as we have no control over it.
Thanks,
Fab
>
> > +};
> > +
> > &hsusb {
> > status = "okay";
> > pinctrl-0 = <&usb0_pins>;
> > @@ -147,6 +202,25 @@
> > VDDIO-supply = <®_3p3v>;
> > VDDD-supply = <®_1p5v>;
> > };
> > +
> > + touch: touchpanel@38 {
> > + compatible = "edt,edt-ft5406";
> > + reg = <0x38>;
> > + interrupt-parent = <&gpio2>;
> > + interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
> > + };
> > +};
> > +
> > +&lvds0 {
> > + status = "okay";
> > +
> > + ports {
> > + port@1 {
> > + lvds0_out: endpoint {
> > + remote-endpoint = <&lvds_receiver_in>;
> > + };
> > + };
> > + };
> > };
> >
> > &pci0 {
> > @@ -180,6 +254,11 @@
> > function = "i2c2";
> > };
> >
> > + pwm3_pins: pwm3 {
> > + groups = "pwm3";
> > + function = "pwm3";
> > + };
> > +
> > scif0_pins: scif0 {
> > groups = "scif0_data_d";
> > function = "scif0";
> > @@ -218,6 +297,12 @@
> > };
> > };
> >
> > +&pwm3 {
> > + pinctrl-0 = <&pwm3_pins>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > +};
> > +
> > &rcar_sound {
> > pinctrl-0 = <&sound_pins>;
> > pinctrl-names = "default";
> > diff --git a/arch/arm/boot/dts/iwg20d-q7-dbcm-ca.dtsi b/arch/arm/boot/dts/iwg20d-q7-dbcm-ca.dtsi
> > index 0e99df2..ede2e0c 100644
> > --- a/arch/arm/boot/dts/iwg20d-q7-dbcm-ca.dtsi
> > +++ b/arch/arm/boot/dts/iwg20d-q7-dbcm-ca.dtsi
> > @@ -39,7 +39,6 @@
> > &du {
> > pinctrl-0 = <&du_pins>;
> > pinctrl-names = "default";
> > - status = "okay";
> >
> > ports {
> > port@0 {
>
> --
> Regards,
>
> Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
