From: Thierry Reding <treding@xxxxxxxxxx> During the discussion of patches that enhance the drm_dp_link helpers it was concluded that these helpers aren't very useful to begin with. Start pushing the equivalent code into individual drivers to ultimately remove them. Signed-off-by: Thierry Reding <treding@xxxxxxxxxx> --- drivers/gpu/drm/bridge/analogix-anx78xx.c | 57 +++++++++++++++++------ 1 file changed, 42 insertions(+), 15 deletions(-) diff --git a/drivers/gpu/drm/bridge/analogix-anx78xx.c b/drivers/gpu/drm/bridge/analogix-anx78xx.c index 9ddc1f3cf841..8bb4793f382b 100644 --- a/drivers/gpu/drm/bridge/analogix-anx78xx.c +++ b/drivers/gpu/drm/bridge/analogix-anx78xx.c @@ -71,7 +71,6 @@ struct anx78xx { struct i2c_client *client; struct edid *edid; struct drm_connector connector; - struct drm_dp_link link; struct anx78xx_platform_data pdata; struct mutex lock; @@ -801,18 +800,34 @@ static int anx78xx_dp_link_training(struct anx78xx *anx78xx) if (err) return err; - /* Check link capabilities */ - err = drm_dp_link_probe(&anx78xx->aux, &anx78xx->link); - if (err < 0) { - DRM_ERROR("Failed to probe link capabilities: %d\n", err); - return err; - } + /* + * Power up the sink (DP_SET_POWER register is only available on DPCD + * v1.1 and later). + */ + if (anx78xx->dpcd[DP_DPCD_REV] >= 0x11) { + err = drm_dp_dpcd_readb(&anx78xx->aux, DP_SET_POWER, &value); + if (err < 0) { + DRM_ERROR("Failed to read DP_SET_POWER register: %d\n", + err); + return err; + } - /* Power up the sink */ - err = drm_dp_link_power_up(&anx78xx->aux, &anx78xx->link); - if (err < 0) { - DRM_ERROR("Failed to power up DisplayPort link: %d\n", err); - return err; + value &= ~DP_SET_POWER_MASK; + value |= DP_SET_POWER_D0; + + err = drm_dp_dpcd_writeb(&anx78xx->aux, DP_SET_POWER, value); + if (err < 0) { + DRM_ERROR("Failed to power up DisplayPort link: %d\n", + err); + return err; + } + + /* + * According to the DP 1.1 specification, a "Sink Device must + * exit the power saving state within 1 ms" (Section 2.5.3.1, + * Table 5-52, "Sink Control Field" (register 0x600). + */ + usleep_range(1000, 2000); } /* Possibly enable downspread on the sink */ @@ -851,15 +866,27 @@ static int anx78xx_dp_link_training(struct anx78xx *anx78xx) if (err) return err; - value = drm_dp_link_rate_to_bw_code(anx78xx->link.rate); + value = drm_dp_max_link_rate(anx78xx->dpcd); + value = drm_dp_link_rate_to_bw_code(value); err = regmap_write(anx78xx->map[I2C_IDX_TX_P0], SP_DP_MAIN_LINK_BW_SET_REG, value); if (err) return err; - err = drm_dp_link_configure(&anx78xx->aux, &anx78xx->link); + err = drm_dp_dpcd_writeb(&anx78xx->aux, DP_LINK_BW_SET, value); + if (err < 0) { + DRM_ERROR("Failed to set link bandwidth: %d\n", err); + return err; + } + + value = drm_dp_max_lane_count(anx78xx->dpcd); + + if (drm_dp_enhanced_frame_cap(anx78xx->dpcd)) + value |= DP_LANE_COUNT_ENHANCED_FRAME_EN; + + err = drm_dp_dpcd_writeb(&anx78xx->aux, DP_LANE_COUNT_SET, value); if (err < 0) { - DRM_ERROR("Failed to configure DisplayPort link: %d\n", err); + DRM_ERROR("Failed to set link lane count: %d\n", err); return err; } -- 2.23.0 _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel