This code is *so* much nicer than before. I hope you feel good about
the changes. It makes me happy to look at this code now.
On Thu, Oct 10, 2019 at 09:34:19AM +0000, Xin Ji wrote:
> +static int edid_read(struct anx7625_data *ctx,
> + u8 offset, u8 *pblock_buf)
> +{
> + int ret, cnt;
> + struct device *dev = &ctx->client->dev;
> +
> + for (cnt = 0; cnt < EDID_TRY_CNT; cnt++) {
> + sp_tx_aux_wr(ctx, offset);
> + /* set I2C read com 0x01 mot = 0 and read 16 bytes */
> + ret = sp_tx_aux_rd(ctx, 0xf1);
> +
> + if (ret) {
> + sp_tx_rst_aux(ctx);
> + DRM_DEV_DEBUG_DRIVER(dev, "edid read failed, reset!\n");
> + cnt++;
I don't think you should increment cnt. It's just a counter.
> + } else {
> + ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client,
> + AP_AUX_BUFF_START,
> + MAX_DPCD_BUFFER_SIZE,
> + pblock_buf);
> + if (!ret)
> + break;
> + }
> + }
> +
> + if (cnt == EDID_TRY_CNT)
And it could mean that "cnt > EDID_TRY_CNT".
> + return -EIO;
> +
> + return 0;
> +}
> +
> +static int segments_edid_read(struct anx7625_data *ctx,
> + u8 segment, u8 *buf, u8 offset)
> +{
> + u8 cnt;
> + int ret;
> + struct device *dev = &ctx->client->dev;
> +
> + /* write address only */
> + ret = anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
> + AP_AUX_ADDR_7_0, 0x30);
> + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
> + AP_AUX_COMMAND, 0x04);
> + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
> + AP_AUX_CTRL_STATUS,
> + AP_AUX_CTRL_ADDRONLY | AP_AUX_CTRL_OP_EN);
> +
> + ret |= wait_aux_op_finish(ctx);
> + /* write segment address */
> + ret |= sp_tx_aux_wr(ctx, segment);
> + /* data read */
> + ret |= anx7625_reg_write(ctx, ctx->i2c.rx_p0_client,
> + AP_AUX_ADDR_7_0, 0x50);
> + if (ret) {
> + DRM_ERROR("IO error : aux initial failed.\n");
> + return ret;
> + }
> +
> + for (cnt = 0; cnt < EDID_TRY_CNT; cnt++) {
> + sp_tx_aux_wr(ctx, offset);
> + /* set I2C read com 0x01 mot = 0 and read 16 bytes */
> + ret = sp_tx_aux_rd(ctx, 0xf1);
> +
> + if (ret) {
> + ret = sp_tx_rst_aux(ctx);
> + DRM_DEV_ERROR(dev, "segment read failed, reset!\n");
> + cnt++;
Same.
> + } else {
> + ret = anx7625_reg_block_read(ctx, ctx->i2c.rx_p0_client,
> + AP_AUX_BUFF_START,
> + MAX_DPCD_BUFFER_SIZE, buf);
> + if (!ret)
> + break;
> + }
> + }
> +
> + if (cnt == EDID_TRY_CNT)
> + return -EIO;
> +
> + return 0;
> +}
regards,
dan carpenter
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
