Add HDMI nodes and other supporting infrastructure in order to support
the external display. This is based on work from Jonathan Marek.
Signed-off-by: Brian Masney <masneyb@xxxxxxxxxxxxx>
Reviewed-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
Changes since v1:
- Regulators always on as a temporary haack.
- Hot plug detect pin for the HDMI bridge needs to be low.
.../qcom-msm8974-lge-nexus5-hammerhead.dts | 142 ++++++++++++++++++
1 file changed, 142 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
index b607c9ff9e12..380a805cd1f0 100644
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -235,6 +235,36 @@
pinctrl-names = "default";
pinctrl-0 = <&wlan_regulator_pin>;
};
+
+ anx_avdd33: avdd33 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "avdd-3p3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on; // FIXME
+
+ gpio = <&pm8941_gpios 26 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&anx_avdd33_pin>;
+ };
+
+ anx_vdd10: vdd10 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vdd-1p0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on; // FIXME
+
+ gpio = <&pm8941_gpios 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&anx_vdd10_pin>;
+ };
};
&soc {
@@ -371,6 +401,40 @@
function = "gpio";
};
};
+
+ hdmi_pin: hdmi {
+ cec {
+ pins = "gpio31";
+ function = "hdmi_cec";
+ };
+
+ ddc {
+ pins = "gpio32", "gpio33";
+ function = "hdmi_ddc";
+ };
+
+ hpd {
+ pins = "gpio34";
+ function = "hdmi_hpd";
+ };
+ };
+
+ anx_msm_pin: anx {
+ irq {
+ pins = "gpio28";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ input-enable;
+ };
+
+ reset {
+ pins = "gpio68";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
};
vibrator@fd8c3450 {
@@ -471,6 +535,28 @@
default-brightness = <200>;
};
};
+
+ anx7808@72 {
+ compatible = "analogix,anx7808";
+ reg = <0x72>;
+ interrupts-extended = <&msmgpio 28 IRQ_TYPE_EDGE_RISING>;
+
+ hpd-gpios = <&pm8941_gpios 13 GPIO_ACTIVE_LOW>;
+ pd-gpios = <&pm8941_gpios 14 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&msmgpio 68 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&anx_msm_pin>, <&anx_pin>;
+
+ dvdd10-supply = <&anx_vdd10>;
+ avdd33-supply = <&anx_avdd33>;
+
+ port {
+ anx7808_in: endpoint {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+ };
};
i2c@f9968000 {
@@ -664,6 +750,29 @@
vddio-supply = <&pm8941_l12>;
};
+
+ hdmi-tx@fd922100 {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_pin>;
+
+ qcom,hdmi-tx-ddc-clk = <&msmgpio 32 GPIO_ACTIVE_HIGH>;
+ qcom,hdmi-tx-ddc-data = <&msmgpio 33 GPIO_ACTIVE_HIGH>;
+ qcom,hdmi-tx-hpd = <&msmgpio 34 GPIO_ACTIVE_HIGH>;
+
+ ports {
+ port@1 {
+ hdmi_out: endpoint {
+ remote-endpoint = <&anx7808_in>;
+ };
+ };
+ };
+ };
+
+ hdmi-phy@fd922500 {
+ status = "ok";
+ };
};
};
@@ -700,6 +809,39 @@
output-high;
line-name = "otg-gpio";
};
+
+ anx_pin: anx {
+ cbldet {
+ pins = "gpio13";
+ function = "normal";
+ input-enable;
+ bias-pull-down;
+ power-source = <PM8941_GPIO_S3>;
+ };
+
+ pd {
+ pins = "gpio14";
+ function = "normal";
+ bias-disable;
+ power-source = <PM8941_GPIO_S3>;
+ };
+ };
+
+ anx_avdd33_pin: anxvdd3 {
+ pins = "gpio26";
+ function = "normal";
+
+ bias-disable;
+ power-source = <PM8941_GPIO_S3>;
+ };
+
+ anx_vdd10_pin: anxvdd1 {
+ pins = "gpio8";
+ function = "normal";
+
+ bias-disable;
+ power-source = <PM8941_GPIO_S3>;
+ };
};
};
};
--
2.21.0
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
