Re: [PATCH v2 2/2] arm64: dts: renesas: Add HiHope RZ/G2M board with idk-1110wr display

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Fabrizio,

Thank you for the patch.

On Thu, Aug 29, 2019 at 12:38:33PM +0100, Fabrizio Castro wrote:
> The HiHope RZ/G2M is advertised as compatible with panel idk-1110wr
> from Advantech, however the panel isn't sold alongside the board.
> A new dts, adding everything that's required to get the panel to
> work the HiHope RZ/G2M, is the most convenient way to support the
> HiHope RZ/G2M when it's connected to the idk-1110wr.
> 
> Signed-off-by: Fabrizio Castro <fabrizio.castro@xxxxxxxxxxxxxx>
> ---
> v1->v2:
> * added space between lvds-connector-en-gpio and curly brace
> 
>  arch/arm64/boot/dts/renesas/Makefile               |  1 +
>  .../r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts        | 86 ++++++++++++++++++++++
>  2 files changed, 87 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts
> 
> diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
> index 42b74c2..5d94301 100644
> --- a/arch/arm64/boot/dts/renesas/Makefile
> +++ b/arch/arm64/boot/dts/renesas/Makefile
> @@ -1,6 +1,7 @@
>  # SPDX-License-Identifier: GPL-2.0
>  dtb-$(CONFIG_ARCH_R8A774A1) += r8a774a1-hihope-rzg2m.dtb
>  dtb-$(CONFIG_ARCH_R8A774A1) += r8a774a1-hihope-rzg2m-ex.dtb
> +dtb-$(CONFIG_ARCH_R8A774A1) += r8a774a1-hihope-rzg2m-ex-idk-1110wr.dtb
>  dtb-$(CONFIG_ARCH_R8A774C0) += r8a774c0-cat874.dtb r8a774c0-ek874.dtb
>  dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-salvator-x.dtb r8a7795-h3ulcb.dtb
>  dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-h3ulcb-kf.dtb
> diff --git a/arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts b/arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts
> new file mode 100644
> index 0000000..67fe04c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts
> @@ -0,0 +1,86 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Device Tree Source for the HiHope RZ/G2M sub board connected to an
> + * Advantech IDK-1110WR 10.1" LVDS panel
> + *
> + * Copyright (C) 2019 Renesas Electronics Corp.
> + */
> +
> +#include "r8a774a1-hihope-rzg2m-ex.dts"
> +
> +/ {
> +	backlight {
> +		compatible = "pwm-backlight";
> +		pwms = <&pwm0 0 50000>;
> +
> +		brightness-levels = <0 2 8 16 32 64 128 255>;
> +		default-brightness-level = <6>;
> +	};
> +
> +	panel-lvds {
> +		compatible = "advantech,idk-1110wr", "panel-lvds";
> +
> +		width-mm = <223>;
> +		height-mm = <125>;
> +
> +		data-mapping = "jeida-24";
> +
> +		panel-timing {
> +			/* 1024x600 @60Hz */
> +			clock-frequency = <51200000>;
> +			hactive = <1024>;
> +			vactive = <600>;
> +			hsync-len = <240>;
> +			hfront-porch = <40>;
> +			hback-porch = <40>;
> +			vfront-porch = <15>;
> +			vback-porch = <10>;
> +			vsync-len = <10>;
> +		};
> +
> +		port {
> +			panel_in: endpoint {
> +				remote-endpoint = <&lvds0_out>;
> +			};
> +		};
> +	};
> +};
> +
> +&gpio1 {
> +	/*
> +	 * When GP1_20 is LOW LVDS0 is connected to the LVDS connector
> +	 * When GP1_20 is HIGH LVDS0 is connected to the LT8918L
> +	 */

I knew that runtime-configurable output routing would be needed one day.
While I'm not opposed to merging this patch as-is, it means that a board
shipping this DT will not support the DSI output. I suppose that's not a
problem as using DSI would require an external DSI panel, which would
require a different DT anyway. In the general case, however,
implementing support in the DU driver for output routing outside the SoC
will be interesting to say the least :-)

Acked-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>

> +	lvds-connector-en-gpio {
> +		gpio-hog;
> +		gpios = <20 GPIO_ACTIVE_HIGH>;
> +		output-low;
> +		line-name = "lvds-connector-en-gpio";
> +	};
> +};
> +
> +&lvds0 {
> +	status = "okay";
> +
> +	ports {
> +		port@1 {
> +			lvds0_out: endpoint {
> +				remote-endpoint = <&panel_in>;
> +			};
> +		};
> +	};
> +};
> +
> +&pfc {
> +	pwm0_pins: pwm0 {
> +		groups = "pwm0";
> +		function = "pwm0";
> +	};
> +};
> +
> +&pwm0 {
> +	pinctrl-0 = <&pwm0_pins>;
> +	pinctrl-names = "default";
> +
> +	status = "okay";
> +};

-- 
Regards,

Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel




[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux