Hi Fabrizio, On Thu, Aug 15, 2019 at 12:04:26PM +0100, Fabrizio Castro wrote: > This panel is handled through the generic lvds-panel bindings, > so only needs its additional compatible specified. > > Some panel-specific documentation can be found here: > https://buy.advantech.eu/Displays/Embedded-LCD-Kits-High-Brightness/model-IDK-2121WR-K2FHA2E.htm > > Signed-off-by: Fabrizio Castro <fabrizio.castro@xxxxxxxxxxxxxx> > > --- > v1->v2: > * Reworked according to Laurent's feedback > * Renamed lvds0_panel_in to panel_in0 > * Renamed lvds1_panel_in to panel_in1 > > Laurent, > > Should this be a .yaml file already? It's not a strict requirement, but I'm sure Rob would really appreciate. I've converted a DT binding to yaml recently (for a panel too), and I have to say I'm impressed by the validation yaml brings, both for DT sources and for DT bindings. It even validates the example in the bindings, which is great. Documentation/devicetree/writing-schema.md should give you a few pointers to get started (in particular make sure you run make dt_binding_check for your new bindings). > .../display/panel/advantech,idk-2121wr.txt | 56 ++++++++++++++++++++++ > 1 file changed, 56 insertions(+) > create mode 100644 Documentation/devicetree/bindings/display/panel/advantech,idk-2121wr.txt > > diff --git a/Documentation/devicetree/bindings/display/panel/advantech,idk-2121wr.txt b/Documentation/devicetree/bindings/display/panel/advantech,idk-2121wr.txt > new file mode 100644 > index 0000000..6ee1d1b > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/panel/advantech,idk-2121wr.txt > @@ -0,0 +1,56 @@ > +Advantech Co., Ltd. IDK-2121WR 21.5" LVDS panel > +=============================================== > + > +Required properties: > +- compatible: should be "advantech,idk-2121wr" followed by "panel-lvds" > + > +This binding is compatible with the lvds-panel binding, which is specified > +in panel-lvds.txt in this directory. > +The panel operates in dual-link mode and thus requires two port nodes, > +the first port node expects odd pixels (1, 3, 5, etc.) and the second port > +expects even pixels (0, 2, 4, etc.). > + > +Example > +------- > + > + panel { > + compatible = "advantech,idk-2121wr", "panel-lvds"; > + > + width-mm = <476>; > + height-mm = <268>; > + > + data-mapping = "vesa-24"; > + > + panel-timing { > + clock-frequency = <148500000>; > + hactive = <1920>; > + vactive = <1080>; > + hsync-len = <44>; > + hfront-porch = <88>; > + hback-porch = <148>; > + vfront-porch = <4>; > + vback-porch = <36>; > + vsync-len = <5>; > + }; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + /* Odd pixels */ > + reg = <0>; > + panel_in0: endpoint { > + remote-endpoint = <&lvds0_out>; > + }; > + }; > + > + port@1 { > + /* Even pixels */ > + reg = <1>; > + panel_in1: endpoint { > + remote-endpoint = <&lvds1_out>; > + }; > + }; > + }; > + }; > -- > 2.7.4 > -- Regards, Laurent Pinchart _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
