On Mon, Aug 12, 2019 at 3:45 PM Jernej Škrabec <jernej.skrabec@xxxxxxxxx> wrote: > > Dne torek, 06. avgust 2019 ob 17:57:39 CEST je megous@xxxxxxxxxx napisal(a): > > From: Ondrej Jirman <megous@xxxxxxxxxx> > > > > This series implements support for Xunlong Orange Pi 3 board. There > > are only a few patches remaining. > > > > - ethernet support - just a DT change (patch 1) > > - HDMI support (patches 2-4) > > > > For some people, ethernet doesn't work after reboot because u-boot doesn't > > support AXP805 PMIC, and will not turn off the etherent PHY regulators. > > So the regulator controlled by gpio will be shut down, but the other one > > controlled by the AXP PMIC will not. > > > > This is a problem only when running with a builtin driver. This needs > > to be fixed in u-boot. > > > > > > Please take a look. > > Is there anything missing? It would be nice to get this in 5.4. There is a lot > of H6 boards which needs DDC bus enable mechanism (part of H6 reference > design), including Beelink GS1 which already has HDMI node in mainline kernel > DT, but due to disabled DDC lines works only with 1024x768 (fallback > resolution in DRM core). I have a few minor comments about patch 1. I think the HDMI bits are good, but I don't have maintainership / commit permissions for drm-misc, so I'll have to wait until someone applies patches 2 and 3 before I apply patch 4. ChenYu > Best regards, > Jernej > > > > > thank you and regards, > > Ondrej Jirman > > > > Changes in v8: > > - added reviewed-by tags > > - dropped already applied patches > > - added more info about the phy initialization issue after reset > > > > Changes in v7: > > - dropped stored reference to connector_pdev as suggested by Jernej > > - added forgotten dt-bindings reviewed-by tag > > > > Changes in v6: > > - added dt-bindings reviewed-by tag > > - fix wording in stmmac commit (as suggested by Sergei) > > > > Changes in v5: > > - dropped already applied patches (pinctrl patches, mmc1 pinconf patch) > > - rename GMAC-3V3 -> GMAC-3V to match the schematic (Jagan) > > - changed hdmi-connector's ddc-supply property to ddc-en-gpios > > (Rob Herring) > > > > Changes in v4: > > - fix checkpatch warnings/style issues > > - use enum in struct sunxi_desc_function for io_bias_cfg_variant > > - collected acked-by's > > - fix compile error in drivers/pinctrl/sunxi/pinctrl-sun9i-a80-r.c:156 > > caused by missing conversion from has_io_bias_cfg struct member > > (I've kept the acked-by, because it's a trivial change, but feel free > > to object.) (reported by Martin A. on github) > > I did not have A80 pinctrl enabled for some reason, so I did not catch > > this sooner. > > - dropped brcm firmware patch (was already applied) > > - dropped the wifi dts patch (will re-send after H6 RTC gets merged, > > along with bluetooth support, in a separate series) > > > > Changes in v3: > > - dropped already applied patches > > - changed pinctrl I/O bias selection constants to enum and renamed > > - added /omit-if-no-ref/ to mmc1_pins > > - made mmc1_pins default pinconf for mmc1 in H6 dtsi > > - move ddc-supply to HDMI connector node, updated patch descriptions, > > changed dt-bindings docs > > > > Changes in v2: > > - added dt-bindings documentation for the board's compatible string > > (suggested by Clement) > > - addressed checkpatch warnings and code formatting issues (on Maxime's > > suggestions) > > - stmmac: dropped useless parenthesis, reworded description of the patch > > (suggested by Sergei) > > - drop useles dev_info() about the selected io bias voltage > > - docummented io voltage bias selection variant macros > > - wifi: marked WiFi DTS patch and realted mmc1_pins as "DO NOT MERGE", > > because wifi depends on H6 RTC support that's not merged yet (suggested > > by Clement) > > - added missing signed-of-bys > > - changed &usb2otg dr_mode to otg, and added a note about VBUS > > - improved wording of HDMI driver's DDC power supply patch > > > > Ondrej Jirman (4): > > arm64: dts: allwinner: orange-pi-3: Enable ethernet > > dt-bindings: display: hdmi-connector: Support DDC bus enable > > drm: sun4i: Add support for enabling DDC I2C bus to sun8i_dw_hdmi glue > > arm64: dts: allwinner: orange-pi-3: Enable HDMI output > > > > .../display/connector/hdmi-connector.txt | 1 + > > .../dts/allwinner/sun50i-h6-orangepi-3.dts | 70 +++++++++++++++++++ > > drivers/gpu/drm/sun4i/sun8i_dw_hdmi.c | 54 ++++++++++++-- > > drivers/gpu/drm/sun4i/sun8i_dw_hdmi.h | 2 + > > 4 files changed, 123 insertions(+), 4 deletions(-) > > > > > -- > You received this message because you are subscribed to the Google Groups "linux-sunxi" group. > To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@xxxxxxxxxxxxxxxx. > To view this discussion on the web, visit https://groups.google.com/d/msgid/linux-sunxi/2218280.0sI6yjypBf%40jernej-laptop. _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
