Hi Bogdan, Thank you for the patch. On Tue, Jul 30, 2019 at 04:17:35PM +0300, Bogdan Togorean wrote: > ADV7535 is a part compatible with ADV7533 but it supports 1080p@60hz and > v1p2 supply is fixed to 1.8V > > Signed-off-by: Bogdan Togorean <bogdan.togorean@xxxxxxxxxx> Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> > --- > .../bindings/display/bridge/adi,adv7511.txt | 23 ++++++++++--------- > 1 file changed, 12 insertions(+), 11 deletions(-) > > diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt > index 2c887536258c..e8ddec5d9d91 100644 > --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt > +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt > @@ -1,10 +1,10 @@ > -Analog Device ADV7511(W)/13/33 HDMI Encoders > +Analog Device ADV7511(W)/13/33/35 HDMI Encoders > ----------------------------------------- > > -The ADV7511, ADV7511W, ADV7513 and ADV7533 are HDMI audio and video transmitters > -compatible with HDMI 1.4 and DVI 1.0. They support color space conversion, > -S/PDIF, CEC and HDCP. ADV7533 supports the DSI interface for input pixels, while > -the others support RGB interface. > +The ADV7511, ADV7511W, ADV7513, ADV7533 and ADV7535 are HDMI audio and video > +transmitters compatible with HDMI 1.4 and DVI 1.0. They support color space > +conversion, S/PDIF, CEC and HDCP. ADV7533/5 supports the DSI interface for input > +pixels, while the others support RGB interface. > > Required properties: > > @@ -13,6 +13,7 @@ Required properties: > "adi,adv7511w" > "adi,adv7513" > "adi,adv7533" > + "adi,adv7535" > > - reg: I2C slave addresses > The ADV7511 internal registers are split into four pages exposed through > @@ -52,14 +53,14 @@ The following input format properties are required except in "rgb 1x" and > - bgvdd-supply: A 1.8V supply that powers up the BGVDD pin. This is > needed only for ADV7511. > > -The following properties are required for ADV7533: > +The following properties are required for ADV7533 and ADV7535: > > - adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should > be one of 1, 2, 3 or 4. > - a2vdd-supply: 1.8V supply that powers up the A2VDD pin on the chip. > - v3p3-supply: A 3.3V supply that powers up the V3P3 pin on the chip. > - v1p2-supply: A supply that powers up the V1P2 pin on the chip. It can be > - either 1.2V or 1.8V. > + either 1.2V or 1.8V for ADV7533 but only 1.8V for ADV7535. > > Optional properties: > > @@ -71,9 +72,9 @@ Optional properties: > - adi,embedded-sync: The input uses synchronization signals embedded in the > data stream (similar to BT.656). Defaults to separate H/V synchronization > signals. > -- adi,disable-timing-generator: Only for ADV7533. Disables the internal timing > - generator. The chip will rely on the sync signals in the DSI data lanes, > - rather than generate its own timings for HDMI output. > +- adi,disable-timing-generator: Only for ADV7533 and ADV7535. Disables the > + internal timing generator. The chip will rely on the sync signals in the > + DSI data lanes, rather than generate its own timings for HDMI output. > - clocks: from common clock binding: reference to the CEC clock. > - clock-names: from common clock binding: must be "cec". > - reg-names : Names of maps with programmable addresses. > @@ -85,7 +86,7 @@ Required nodes: > The ADV7511 has two video ports. Their connections are modelled using the OF > graph bindings specified in Documentation/devicetree/bindings/graph.txt. > > -- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533, the > +- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533/5, the > remote endpoint phandle should be a reference to a valid mipi_dsi_host device > node. > - Video port 1 for the HDMI output -- Regards, Laurent Pinchart _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
