Hello Rob,
my fault, sorry, backlight should not be required.
I'll fix this in the next patch version.
I'd like to post the DT bindings in the YAML format.
Work-in-progress YAML bindings file is in the attachment,
any comments would be highly appreciated.
Kind regards
Josef
st 24. 7. 2019 v 21:57 odesílatel Rob Herring <robh@xxxxxxxxxx> napsal:
>
> On Mon, Jul 08, 2019 at 04:56:17PM +0200, Josef Lusticky wrote:
> > ILI9341 supports both SPI input mode and parallel RGB input mode.
> > This commit adds parallel RGB input mode bindings.
> >
> > Signed-off-by: Josef Lusticky <josef@xxxxxxxxxxx>
> > ---
> > .../bindings/display/ilitek,ili9341.txt | 67 ++++++++++++++++---
> > 1 file changed, 56 insertions(+), 11 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/display/ilitek,ili9341.txt b/Documentation/devicetree/bindings/display/ilitek,ili9341.txt
> > index 169b32e4ee4e..629f38a1d0cd 100644
> > --- a/Documentation/devicetree/bindings/display/ilitek,ili9341.txt
> > +++ b/Documentation/devicetree/bindings/display/ilitek,ili9341.txt
> > @@ -1,27 +1,72 @@
> > Ilitek ILI9341 display panels
> >
> > -This binding is for display panels using an Ilitek ILI9341 controller in SPI
> > -mode.
> > +This binding is for display panels using an Ilitek ILI9341 controller.
> > +The display panels are supported in the following graphical input modes:
> > +- SPI input mode
> > + MIPI-DBI Type 3 Option 1 or Option 3 is used to transfer
> > + commands and graphical data
> > +- parallel RGB input mode
> > + MIPI-DBI Type 3 Option 1 or Option 3 is used for commands
> > + MIPI-DPI 18-bit parallel RGB connection is used to transfer
> > + graphical data
> >
> > -Required properties:
> > -- compatible: "adafruit,yx240qv29", "ilitek,ili9341"
> > -- dc-gpios: D/C pin
> > -- reset-gpios: Reset pin
> > +
> > +SPI input mode:
> >
> > The node for this driver must be a child node of a SPI controller, hence
> > -all mandatory properties described in ../spi/spi-bus.txt must be specified.
> > +all mandatory properties described in spi/spi-bus.txt must be specified.
> > +
> > +Required properties in SPI input mode:
> > +- compatible: "adafruit,yx240qv29", "ilitek,ili9341"
> > +- backlight: phandle of the backlight device attached to the panel
>
> Why is backlight now required?
>
> > +
> > +Optional properties in SPI input mode:
> > +- rotation: panel rotation in degrees counter clockwise (0,90,180,270)
> > +- dc-gpios: GPIO spec for the D/C pin, see gpio/gpio.txt
> > +- reset-gpios: GPIO spec for the reset pin, see gpio/gpio.txt
> > +
> > +
> > +Parallel RGB input mode:
> > +
> > +The node for this driver must be a child node of a SPI controller, hence
> > +all mandatory properties described in spi/spi-bus.txt must be specified.
> > +
> > +Required properties in parallel RGB input mode:
> > +- compatible: "displaytech,dt024ctft", "ilitek,ili9341"
> > +- backlight: phandle of the backlight device attached to the panel
> > +
> > +Optional properties in parallel RGB input mode:
> > +- dc-gpios: GPIO spec for the D/C pin, see gpio/gpio.txt
> > +- reset-gpios: GPIO spec for the reset pin, see gpio/gpio.txt
> >
> > -Optional properties:
> > -- rotation: panel rotation in degrees counter clockwise (0,90,180,270)
> > -- backlight: phandle of the backlight device attached to the panel
> > +In parallel RGB input mode,
> > +the device node can contain one 'port' child node with one child
> > +'endpoint' node, according to the bindings defined in
> > +media/video-interfaces.txt. This node should describe panel's video bus.
> >
> > -Example:
> > +
> > +Example in SPI input mode:
> > display@0{
> > compatible = "adafruit,yx240qv29", "ilitek,ili9341";
> > reg = <0>;
> > spi-max-frequency = <32000000>;
> > dc-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
> > reset-gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
> > + backlight = <&backlight>;
> > rotation = <270>;
> > + };
> > +
> > +Example in parallel RGB input mode:
> > + panel@{
> > + compatible = "displaytech,dt024ctft", "ilitek,ili9341";
> > + reg = <0>;
> > + spi-max-frequency = <32000000>;
> > + dc-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
> > + reset-gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
> > backlight = <&backlight>;
> > + port {
> > + panel_in: endpoint {
> > + remote-endpoint = <&display_out>;
> > + };
> > + };
> > };
> > --
> > 2.20.1
> >
# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/display/panel/ilitek,ili9341.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Ilitek ILI9341 display panels
maintainers:
- Josef Lusticky <josef@xxxxxxxxxxx>
description: |
This binding is for display panels using an Ilitek ILI9341 controller.
The display panels are supported in the following graphical input modes:
SPI input mode
MIPI-DBI Type 3 Option 1 or Option 3 is used to transfer
commands and graphical data
Parallel RGB input mode
MIPI-DBI Type 3 Option 1 or Option 3 is used for commands
MIPI-DPI 18-bit parallel RGB connection is used to transfer
graphical data
allOf:
- $ref: /schemas/spi/spi-controller.yaml#
properties:
compatible:
items:
- const: adafruit,yx240qv29
backlight: true
reset-gpios: true
dc-gpios: true
rotation: true
port: true
additionalProperties: false
required:
- compatible
- backlight
Example in SPI input mode:
display@0{
compatible = "adafruit,yx240qv29", "ilitek,ili9341";
reg = <0>;
spi-max-frequency = <32000000>;
dc-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
reset-gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
backlight = <&backlight>;
rotation = <270>;
};
Example in parallel RGB input mode:
panel@{
compatible = "displaytech,dt024ctft", "ilitek,ili9341";
reg = <0>;
spi-max-frequency = <32000000>;
dc-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
reset-gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
backlight = <&backlight>;
port {
panel_in: endpoint {
remote-endpoint = <&display_out>;
};
};
};
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
