On 01/10/17 04:56, Jernej Škrabec wrote: > Hi, > > Dne sobota, 30. september 2017 ob 13:58:03 CEST je Alexey Kardashevskiy > napisal(a): >> On 21/09/17 06:01, Jernej Skrabec wrote: >>> [added media mailing list due to CEC question] >>> >>> This patch series adds a HDMI glue driver for Allwinner H3 SoC. For now, >>> only video and CEC functionality is supported. Audio needs more tweaks. >>> >>> Series is based on the H3 DE2 patch series available on mailing list: >>> http://lists.infradead.org/pipermail/linux-arm-kernel/2017-August/522697.h >>> tml (ignore patches marked with [NOT FOR REVIEW NOW] tag) >>> >>> Patch 1 adds support for polling plug detection since custom PHY used here >>> doesn't support HPD interrupt. >>> >>> Patch 2 enables overflow workaround for v1.32a. This HDMI controller >>> exhibits same issues as HDMI controller used in iMX6 SoCs. >>> >>> Patch 3 adds CLK_SET_RATE_PARENT to hdmi clock. >>> >>> Patch 4 adds dt bindings documentation. >>> >>> Patch 5 adds actual H3 HDMI glue driver. >>> >>> Patch 6 and 7 add HDMI node to DT and enable it where needed. >>> >>> Allwinner used DW HDMI controller in a non standard way: >>> - register offsets obfuscation layer, which can fortunately be turned off >>> - register read lock, which has to be disabled by magic number >>> - custom PHY, which have to be initialized before DW HDMI controller >>> - non standard clocks >>> - no HPD interrupt >>> >>> Because of that, I have two questions: >>> - Since HPD have to be polled, is it enough just to enable poll mode? I'm >>> >>> mainly concerned about invalidating CEC address here. >>> >>> - PHY has to be initialized before DW HDMI controller to disable offset >>> >>> obfuscation and read lock among other things. This means that all clocks >>> have to be enabled in glue driver. This poses a problem, since when >>> using component model, dw-hdmi bridge uses drvdata for it's own private >>> data and prevents glue layer to pass a pointer to unbind function, >>> where clocks should be disabled. I noticed same issue in meson DW HDMI >>> glue driver, where clocks are also not disabled when unbind callback is >>> called. I noticed that when H3 SoC is shutdown, HDMI output is still >>> enabled and lastest image is shown on monitor until it is unplugged >>> from power supply. Is there any simple solution to this? >>> >>> Chen-Yu, >>> TL Lim was unable to obtain any answer from Allwinner about HDMI clocks. I >>> think it is safe to assume that divider in HDMI clock doesn't have any >>> effect. >>> >>> Branch based on linux-next from 1. September with integrated patches is >>> available here: >>> https://github.com/jernejsk/linux-1/tree/h3_hdmi_rfc >> >> Out of curiosity I tried this one and got: >> >> >> >> [ 0.071711] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO >> [ 0.074809] sun8i-h3-pinctrl 1c20800.pinctrl: initialized sunXi PIO >> driver [ 0.076167] sun8i-h3-r-pinctrl 1f02c00.pinctrl: initialized sunXi >> PIO driver [ 0.148009] ------------[ cut here ]------------ >> [ 0.148035] WARNING: CPU: 0 PID: 1 at >> drivers/clk/sunxi-ng/ccu_common.c:41 ccu_nm_set_rate+0x1d0/0x274 >> [ 0.148046] CPU: 0 PID: 1 Comm: swapper/0 Not tainted >> 4.13.0-rc6-next-20170825-aik-aik #24 >> [ 0.148051] Hardware name: Allwinner sun8i Family >> [ 0.148082] [<c010de6c>] (unwind_backtrace) from [<c010b260>] >> (show_stack+0x10/0x14) >> [ 0.148101] [<c010b260>] (show_stack) from [<c077a464>] >> (dump_stack+0x84/0x98) >> [ 0.148117] [<c077a464>] (dump_stack) from [<c011abe0>] >> (__warn+0xe0/0xfc) [ 0.148132] [<c011abe0>] (__warn) from [<c011acac>] >> (warn_slowpath_null+0x20/0x28) >> [ 0.148145] [<c011acac>] (warn_slowpath_null) from [<c03d1888>] >> (ccu_nm_set_rate+0x1d0/0x274) >> [ 0.148161] [<c03d1888>] (ccu_nm_set_rate) from [<c03c78b4>] >> (clk_change_rate+0x19c/0x250) >> [ 0.148175] [<c03c78b4>] (clk_change_rate) from [<c03c7b7c>] >> (clk_core_set_rate_nolock+0x68/0xb0) >> [ 0.148187] [<c03c7b7c>] (clk_core_set_rate_nolock) from [<c03c8134>] >> (clk_set_rate+0x20/0x30) >> [ 0.148202] [<c03c8134>] (clk_set_rate) from [<c03cc560>] >> (of_clk_set_defaults+0x200/0x364) >> [ 0.148219] [<c03cc560>] (of_clk_set_defaults) from [<c045427c>] >> (platform_drv_probe+0x18/0xb0) >> [ 0.148233] [<c045427c>] (platform_drv_probe) from [<c0452efc>] >> (driver_probe_device+0x234/0x2e8) >> [ 0.148246] [<c0452efc>] (driver_probe_device) from [<c0453068>] >> (__driver_attach+0xb8/0xbc) >> [ 0.148258] [<c0453068>] (__driver_attach) from [<c0451414[ 1.336154] >> Unable to handle kernel NULL pointer dereference at virtual address 00000008 >> > > Patch for that is already merged upstream and can be found here: > https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/ > drivers/clk/sunxi-ng?id=62d212bdb022deeb875f92f6e376c799e3f35eca Lovely, it works, thanks! >> and a bit later: >> >> [ 1.995572] Rebooting in 10 seconds.. > > I'm not sure about that one. Kernel config issue? Yup, I did not have CMA enabled. -- Alexey _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel