The H3 ES1.x exhibits dot clock duty cycle stability issues. We can work
around them by configuring the DPLL to twice the desired frequency,
coupled with a /2 post-divider. This isn't needed on other SoCs and
breaks HDMI output on M3-W for a currently unknown reason, so restrict
the workaround to H3 ES1.x.
>From an implementation point of view, move work around handling outside
of the rcar_du_dpll_divider() function by requesting a x2 DPLL output
frequency explicitly. The existing post-divider calculation mechanism
will then take care of dividing the clock by two automatically.
While at it, print a more useful debugging message to ease debugging
clock rate issues.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@xxxxxxxxxxxxxxxx>
---
drivers/gpu/drm/rcar-du/rcar_du_crtc.c | 37 +++++++++++++++++++++++++---------
1 file changed, 27 insertions(+), 10 deletions(-)
diff --git a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
index 8f942ebdd0c6..6c29981377c0 100644
--- a/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
+++ b/drivers/gpu/drm/rcar-du/rcar_du_crtc.c
@@ -13,6 +13,7 @@
#include <linux/clk.h>
#include <linux/mutex.h>
+#include <linux/sys_soc.h>
#include <drm/drmP.h>
#include <drm/drm_atomic.h>
@@ -129,10 +130,8 @@ static void rcar_du_dpll_divider(struct rcar_du_crtc *rcrtc,
for (fdpll = 1; fdpll < 32; fdpll++) {
unsigned long output;
- /* 1/2 (FRQSEL=1) for duty rate 50% */
output = input * (n + 1) / (m + 1)
- / (fdpll + 1) / 2;
-
+ / (fdpll + 1);
if (output >= 400000000)
continue;
@@ -158,6 +157,11 @@ static void rcar_du_dpll_divider(struct rcar_du_crtc *rcrtc,
best_diff);
}
+static const struct soc_device_attribute rcar_du_r8a7795_es1[] = {
+ { .soc_id = "r8a7795", .revision = "ES1.*" },
+ { /* sentinel */ }
+};
+
static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc)
{
const struct drm_display_mode *mode = &rcrtc->crtc.state->adjusted_mode;
@@ -185,7 +189,20 @@ static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc)
extclk = clk_get_rate(rcrtc->extclock);
if (rcdu->info->dpll_ch & (1 << rcrtc->index)) {
- rcar_du_dpll_divider(rcrtc, &dpll, extclk, mode_clock);
+ unsigned long target = mode_clock;
+
+ /*
+ * The H3 ES1.x exhibits dot clock duty cycle stability
+ * issues. We can work around them by configuring the
+ * DPLL to twice the desired frequency, coupled with a
+ * /2 post-divider. This isn't needed on other SoCs and
+ * breaks HDMI output on M3-W for a currently unknown
+ * reason, so restrict the workaround to H3 ES1.x.
+ */
+ if (soc_device_match(rcar_du_r8a7795_es1))
+ target *= 2;
+
+ rcar_du_dpll_divider(rcrtc, &dpll, extclk, target);
extclk = dpll.output;
}
@@ -197,8 +214,6 @@ static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc)
if (abs((long)extrate - (long)mode_clock) <
abs((long)rate - (long)mode_clock)) {
- dev_dbg(rcrtc->group->dev->dev,
- "crtc%u: using external clock\n", rcrtc->index);
if (rcdu->info->dpll_ch & (1 << rcrtc->index)) {
u32 dpllcr = DPLLCR_CODE | DPLLCR_CLKE
@@ -215,12 +230,14 @@ static void rcar_du_crtc_set_display_timing(struct rcar_du_crtc *rcrtc)
rcar_du_group_write(rcrtc->group, DPLLCR,
dpllcr);
-
- escr = ESCR_DCLKSEL_DCLKIN | 1;
- } else {
- escr = ESCR_DCLKSEL_DCLKIN | extdiv;
}
+
+ escr = ESCR_DCLKSEL_DCLKIN | extdiv;
}
+
+ dev_dbg(rcrtc->group->dev->dev,
+ "mode clock %lu extrate %lu rate %lu ESCR 0x%08x\n",
+ mode_clock, extrate, rate, escr);
}
rcar_du_group_write(rcrtc->group, rcrtc->index % 2 ? ESCR2 : ESCR,
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
