Hi Jean-François,
Thank you for the patch.
On Monday 28 Nov 2016 19:02:39 Jean-Francois Moine wrote:
> Signed-off-by: Jean-Francois Moine <moinejf@xxxxxxx>
> ---
> .../bindings/display/sunxi/sun8i-de2.txt | 121 ++++++++++++++++++
> 1 file changed, 121 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/display/sunxi/sun8i-de2.txt
>
> diff --git a/Documentation/devicetree/bindings/display/sunxi/sun8i-de2.txt
> b/Documentation/devicetree/bindings/display/sunxi/sun8i-de2.txt new file
> mode 100644
> index 0000000..edf38b8
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/sunxi/sun8i-de2.txt
> @@ -0,0 +1,121 @@
> +Allwinner sun8i Display Engine 2 subsystem
> +==========================================
> +
> +The Allwinner DE2 subsystem contains a display controller (DE2),
> +one or two LCD controllers (Timing CONtrollers) and their external
> +interfaces (encoders/connectors).
> +
> + +-----------+
> + | DE2 |
> + | |
> + | +-------+ |
> + plane --->| | | +------+
> + | | mixer |---->| TCON |---> encoder ---> display
> + plane --->| | | +------+ connector device
> + | +-------+ |
> + | |
> + | +-------+ |
> + plane --->| | | +------+
> + | | mixer |---->| TCON |---> encoder ---> display
> + plane --->| | | +------+ connector device
> + | +-------+ |
> + +-----------+
> +
> +The DE2 contains a processor which mixes the input planes and creates
> +the images which are sent to the TCONs.
> +From the software point of vue, there are 2 independent real-time
> +mixers, each one being statically associated to one TCON.
> +
> +The TCONs adjust the image format to the one of the display device.
> +
> +Display controller (DE2)
> +========================
> +
> +Required properties:
> +
> +- compatible: value should be one of the following
> + "allwinner,sun8i-a83t-display-engine"
> + "allwinner,sun8i-h3-display-engine"
> +
> +- reg: base address and size of the I/O memory
> +
> +- clocks: must include clock specifiers corresponding to entries in the
> + clock-names property.
> +
> +- clock-names: must contain
> + "bus": bus gate
> + "clock": clock
> +
> +- resets: phandle to the reset of the device
> +
> +- ports: must contain a list of 2 phandles, indexed by mixer number,
> + and pointing to display interface ports of TCONs
> +
> +LCD controller (TCON)
> +=====================
> +
> +Required properties:
> +
> +- compatible: should be
> + "allwinner,sun8i-a83t-tcon"
> +
> +- reg: base address and size of the I/O memory
> +
> +- clocks: must include clock specifiers corresponding to entries in the
> + clock-names property.
> +
> +- clock-names: must contain
> + "bus": bus gate
> + "clock": pixel clock
> +
> +- resets: phandle to the reset of the device
> +
> +- interrupts: interrupt number for the TCON
> +
> +- port: port node with endpoint definitions as defined in
> + Documentation/devicetree/bindings/media/video-interfaces.txt
> +
> +Example:
> +
> + de: de-controller@01000000 {
> + compatible = "allwinner,sun8i-h3-display-engine";
> + reg = <0x01000000 0x400000>;
> + clocks = <&ccu CLK_BUS_DE>, <&ccu CLK_DE>;
> + clock-names = "bus", "clock";
> + resets = <&ccu RST_BUS_DE>;
> + ports = <&tcon0_p>, <&tcon1_p>;
This isn't how the OF graph DT bindings are used. You should instead have
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
de_out_0: endpoint {
remote_endpoint = <&tcon0_hdmi>;
};
};
port@1 {
/* No endpoint as the port is not connected */
};
};
> + };
> +
> + tcon0: lcd-controller@01c0c000 {
> + compatible = "allwinner,sun8i-a83t-tcon";
> + reg = <0x01c0c000 0x400>;
> + clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
> + clock-names = "bus", "clock";
> + resets = <&ccu RST_BUS_TCON0>;
> + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + tcon0_p: port {
> + tcon0_hdmi: endpoint {
> + remote-endpoint = <&hdmi_tcon0>;
> + };
> + };
and here
port {
tcon0_hdmi: endpoint {
remote-endpoint = <&de_out_0>;
};
};
> + };
> +
> + /* not used */
> + tcon1: lcd-controller@01c0d000 {
> + compatible = "allwinner,sun8i-h3-tcon";
> + reg = <0x01c0d000 0x400>;
> + clocks = <&ccu CLK_BUS_TCON1>,
> + <&ccu CLK_TCON0>; /* no clock */
> + clock-names = "bus", "clock";
> + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + tcon1_p: port {
> + endpoint {
> + /* empty */
> + };
> + };
and here
port {
/* No endpoint as the port is not connected */
};
(although I'm not sure why you don't connect it)
> + };
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
