> From: Jason Gunthorpe <jgg@xxxxxxxxxx> > Sent: Friday, August 7, 2020 8:20 PM > > On Wed, Aug 05, 2020 at 07:22:58PM -0600, Alex Williamson wrote: > > > If you see this as an abuse of the framework, then let's identify those > > specific issues and come up with a better approach. As we've discussed > > before, things like basic PCI config space emulation are acceptable > > overhead and low risk (imo) and some degree of register emulation is > > well within the territory of an mdev driver. > > What troubles me is that idxd already has a direct userspace interface > to its HW, and does userspace DMA. The purpose of this mdev is to > provide a second direct userspace interface that is a little different > and trivially plugs into the virtualization stack. No. Userspace DMA and subdevice passthrough (what mdev provides) are two distinct usages IMO (at least in idxd context). and this might be the main divergence between us, thus let me put more words here. If we could reach consensus in this matter, which direction to go would be clearer. First, a passthrough interface requires some unique requirements which are not commonly observed in an userspace DMA interface, e.g.: - Tracking DMA dirty pages for live migration; - A set of interfaces for using SVA inside guest; * PASID allocation/free (on some platforms); * bind/unbind guest mm/page table (nested translation); * invalidate IOMMU cache/iotlb for guest page table changes; * report page request from device to guest; * forward page response from guest to device; - Configuring irqbypass for posted interrupt; - ... Second, a passthrough interface requires delegating raw controllability of subdevice to guest driver, while the same delegation might not be required for implementing an userspace DMA interface (especially for modern devices which support SVA). For example, idxd allows following setting per wq (guest driver may configure them in any combination): - put in dedicated or shared mode; - enable/disable SVA; - Associate guest-provided PASID to MSI/IMS entry; - set threshold; - allow/deny privileged access; - allocate/free interrupt handle (enlightened for guest); - collect error status; - ... We plan to support idxd userspace DMA with SVA. The driver just needs to prepare a wq with a predefined configuration (e.g. shared, SVA, etc.), bind the process mm to IOMMU (non-nested) and then map the portal to userspace. The goal that userspace can do DMA to associated wq doesn't change the fact that the wq is still *owned* and *controlled* by kernel driver. However as far as passthrough is concerned, the wq is considered 'owned' by the guest driver thus we need an interface which can support low-level *controllability* from guest driver. It is sort of a mess in uAPI when mixing the two together. Based on above two reasons, we see distinct requirements between userspace DMA and passthrough interfaces, at least in idxd context (though other devices may have less distinction in-between). Therefore, we didn't see the value/necessity of reinventing the wheel that mdev already handles well to evolve an simple application-oriented usespace DMA interface to a complex guest-driver-oriented passthrough interface. The complexity of doing so would incur far more kernel-side changes than the portion of emulation code that you've been concerned about... > > I don't think VFIO should be the only entry point to > virtualization. If we say the universe of devices doing user space DMA > must also implement a VFIO mdev to plug into virtualization then it > will be alot of mdevs. Certainly VFIO will not be the only entry point. and This has to be a case-by-case decision. If an userspace DMA interface can be easily adapted to be a passthrough one, it might be the choice. But for idxd, we see mdev a much better fit here, given the big difference between what userspace DMA requires and what guest driver requires in this hw. > > I would prefer to see that the existing userspace interface have the > extra needed bits for virtualization (eg by having appropriate > internal kernel APIs to make this easy) and all the emulation to build > the synthetic PCI device be done in userspace. In the end what decides the direction is the amount of changes that we have to put in kernel, not whether we call it 'emulation'. For idxd, adding special passthrough requirements (guest SVA, dirty tracking, etc.) and raw controllability to the simple userspace DMA interface is for sure making kernel more complex than reusing the mdev framework (plus some degree of emulation mockup behind). Not to mention the merit of uAPI compatibility with mdev... Thanks Kevin
