On 2/5/18 1:00 PM, Mikulas Patocka wrote:
>
>
> On Mon, 5 Feb 2018, Jens Axboe wrote:
>
>> On 2/5/18 12:22 PM, Jens Axboe wrote:
>>> On 2/5/18 12:11 PM, Mikulas Patocka wrote:
>>>> I have a workload where one process sends many asynchronous write bios
>>>> (without waiting for them) and another process sends synchronous flush
>>>> bios. During this workload, writeback throttling throttles down to one
>>>> outstanding bio, and this incorrect throttling causes performance
>>>> degradation (all write bios sleep in __wbt_wait and they couldn't be sent
>>>> in parallel).
>>>>
>>>> The reason for this throttling is that wbt_data_dir counts flush requests
>>>> in the read bucket. The flush requests (that take quite a long time)
>>>> trigger this condition repeatedly:
>>>> if (stat[READ].min > rwb->min_lat_nsec)
>>>> and that condition causes scale down to one outstanding request, despite
>>>> the fact that there are no read bios at all.
>>>>
>>>> A similar problem could also show up with REQ_OP_ZONE_REPORT and
>>>> REQ_OP_ZONE_RESET - they are also counted in the read bucket.
>>>>
>>>> This patch fixes the function wbt_data_dir, so that only REQ_OP_READ
>>>> requests are counted in the read bucket. The patch improves SATA
>>>> write+flush throughput from 130MB/s to 350MB/s.
>>>
>>> Good catch. But I do wonder if we should account them at all. It
>>> might make sense to account flushes as writes, but we really
>>> should not account anything that isn't regular read/write IO
>>> related.
>>>
>>> Something like the below? Potentially including REQ_OP_FLUSH in the
>>> write latencies as well.
>>
>> Thinking about it, flush should just be counted as writes, and the
>> rest disregarded. Ala below.
>>
>>
>> diff --git a/block/blk-wbt.c b/block/blk-wbt.c
>> index ae8de9780085..f92fc84b5e2c 100644
>> --- a/block/blk-wbt.c
>> +++ b/block/blk-wbt.c
>> @@ -697,7 +697,15 @@ u64 wbt_default_latency_nsec(struct request_queue *q)
>>
>> static int wbt_data_dir(const struct request *rq)
>> {
>> - return rq_data_dir(rq);
>> + const int op = req_op(rq);
>> +
>> + if (op == REQ_OP_READ)
>> + return READ;
>> + else if (op == REQ_OP_WRITE || op == REQ_OP_FLUSH)
>> + return WRITE;
>> +
>> + /* don't account */
>> + return -1;
>> }
>>
>> int wbt_init(struct request_queue *q)
>>
>> --
>> Jens Axboe
>
> Yes, this works.
OK good, I'll queue that up then.
> BTW. write throttling still causes some performance degradation (350MB/s
> vs. 500MB/s without throttling) - should there be some logic that disables
> write throttling if no sync requests are received?
>
> Something like - if there's sync read, enable write throttling - if there
> were no sync reads in the last 5 seconds, disable write throttling?
blk-wbt maintains a baseline that isn't too deep into writes, or you run
into problems exactly when a sync or read request does come in after 5
seconds, or whatever heuristic you choose. So that's very much by
design. It does allow steps to go negative if no reads have been seen,
but only so much so, and it bounces back immediately when one is seen.
--
Jens Axboe
--
dm-devel mailing list
dm-devel@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/dm-devel
