On 12/20/2016 10:41 AM, Binoy Jayan wrote: > At a high level the goal is to maximize the size of data blocks that get passed > to hardware accelerators, minimizing the overhead from setting up and tearing > down operations in the hardware. Currently dm-crypt itself is a big blocker as > it manually implements ESSIV and similar algorithms which allow per-block > encryption of the data so the low level operations from the crypto API can > only operate on a single block. This is done because currently the crypto API > doesn't have software implementations of these algorithms itself so dm-crypt > can't rely on it being able to provide the functionality. The plan to address > this was to provide some software implementations in the crypto API, then > update dm-crypt to rely on those. Even for a pure software implementation > with no hardware acceleration that should hopefully provide a small > optimization as we need to call into the crypto API less often but it's likely > to be marginal given the overhead of crypto, the real win would be on a system > that has an accelerator that can replace the software implementation. > > Currently dm-crypt handles data only in single blocks. This means that it can't > make good use of hardware cryptography engines since there is an overhead to > each transaction with the engine but transfers must be split into block sized > chunks. Allowing the transfer of larger blocks e.g. 'struct bio', could > mitigate against these costs and could improve performance in operating systems > with encrypted filesystems. Although qualcomm chipsets support another variant > of the device-mapper dm-req-crypt, it is not something generic and in > mainline-able state. Also, it only supports 'XTS-AES' mode of encryption and > is not compatible with other modes supported by dm-crypt. So the core problem is that your crypto accelerator can operate efficiently only with bigger batch sizes. How big blocks your crypto hw need to be able to operate more efficiently? What about 4k blocks (no batches), could it be usable trade-off? With some (backward incompatible) changes in LUKS format I would like to see support for encryption blocks equivalent to sectors size, so it basically means for 4k drive 4k encryption block. (This should decrease overhead, now is everything processed on 512 blocks only.) Support of bigger block sizes would be unsafe without additional mechanism that provides atomic writes of multiple sectors. Maybe it applies to 4k as well on some devices though...) The above is not going against your proposal, I am just curious if this is enough to provide better performance on your hw accelerator or not. Milan > However, there are some challenges and a few possibilities to address this. I > request you to provide your suggestions on whether the points mentioned below > makes sense and if it could be done differently. > > 1. Move the 'real' IV generation algorithms to crypto layer (e.g. essiv) > 2. Increase the 'length' of the scatterlist nodes used in the crypto api. It > can be made equal to the size of a main memory segment (as defined in > 'struct bio') as they are physcially contiguous. > 3. Multiple segments in 'struct bio' can be represented as scatterlist of all > segments in a 'struct bio'. > > 4. Move algorithms 'lmk' and 'tcw' (which are IV combined with hacks to the > cbc mode) to create a customized cbc algorithm, implemented in a seperate > file (e.g. cbc_lmk.c/cbc_tcw.c). As Milan suggested, these can't be treated > as real IVs as these include hacks to the cbc mode (and directly manipulate > encrypted data). > > 5. Move key selection logic to user space or always assume keycount as '1' > (as mentioned in the dm-crypt param format below) so that the key selection > logic does not have to be dependent on the sector number. This is necessary > as the key is selected otherwise based on sector number: > > key_index = sector & (key_count - 1) > > If block size for scatterlist nodes are increased beyond sector boundary > (which is what we plan to achieve, for performance), the key set for every > cipher operation cannot be changed at the sector level. > > dm-crypt param format : cipher[:keycount]-mode-iv:ivopts > Example : aes:2-cbc-essiv:sha256 > > Also as Milan suggested, it is not wise to move the key selection logic to > the crypto layer as it will prevent any changes to the key structure later. > > The following is a reference to an earlier patchset. It had the cipher mode > 'cbc' mixed up with the IV algorithms and is usually not the preferred way. > > Reference: > https://lkml.org/lkml/2016/12/13/65 > https://lkml.org/lkml/2016/12/13/66 > -- dm-devel mailing list dm-devel@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/dm-devel
