Add the binding for the Texas Instruments LM3533 lighting power
solution.
Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxxxxxx>
---
Documentation/devicetree/bindings/mfd/lm3533.txt | 183 +++++++++++++++++++++++
1 file changed, 183 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/lm3533.txt
diff --git a/Documentation/devicetree/bindings/mfd/lm3533.txt b/Documentation/devicetree/bindings/mfd/lm3533.txt
new file mode 100644
index 000000000000..3cc41695a544
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/lm3533.txt
@@ -0,0 +1,183 @@
+Texas Instruments LM3533 binding
+
+This binding describes the Texas Instruments LM3533, a lighting power solution
+for smartphone handsets. The common properties are described directly in the
+node, while each individual component are described in an optional subnode.
+
+- compatible:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must be:
+ "ti,lm3533"
+
+- reg:
+ Usage: required
+ Value type: <u32>
+ Definition: i2c address of the LM3533 chip
+
+- ti,hwen-gpios:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: reference to gpio pin connected to the HWEN input; as
+ specified in "gpio/gpio.txt"
+
+- ti,als-supply:
+ Usage: optional
+ Value type: <prop-encoded-array>
+ Definition: reference to regulator powering the V_als input; as
+ specified in "regulator/regulator.txt"
+
+- ti,boost-freq:
+ Usage: required
+ Value type: <u32>
+ Definition: switch-frequency of the boost converter, must be either:
+ 500000 or 1000000
+
+- ti,boost-ovp:
+ Usage: required
+ Value type: <u32>
+ Definition: over voltage protection limit, must be one of: 16, 24, 32
+ or 40
+
+- #address-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 1
+
+- #size-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 0
+
+= ALS SUBNODE
+The als subnode must be named "als", it carries the als related properties.
+
+- ti,als-resistance:
+ Usage: required (unless ti,pwm-mode is specified)
+ Value type: <u32>
+ Definition: specifies the resistor value (R_als), in Ohm. Valid values
+ ranges from 200kOhm to 1574Ohm.
+
+- ti,pwm-mode:
+ Usage: optional
+ Value type: <empty>
+ Definition: specifies, if present, that the als should operate in pwm
+ mode - rather than analog mode
+
+= BACKLIGHT NODES
+Backlight subnodes must be named "backlight", they carry the backlight related
+properties.
+
+- reg:
+ Usage: required
+ Value type: <u32>
+ Definition: specifies which of the two backlights this node corresponds
+ to
+
+- default-brightness:
+ Usage: optional
+ Value type: <32>
+ Definition: specifies the default brightness for the backlight, in
+ units of brightness [0-255]
+
+- label:
+ Usage: required
+ Value type: <string>
+ Definition: specifies a name of this backlight
+
+- led-max-microamp:
+ Usage: required
+ Value type: <u32>
+ Definition: specifies the max current for this backlight, in uA, as
+ described in "leds/common.txt"
+
+- ti,pwm-zones:
+ Usage: optional
+ Value type: <u32 list>
+ Definition: lists the ALS zones to be PWM controlled for this backlight,
+ the values in the list are in the range [0 - 4]
+
+= LED NODES
+LED subnodes must be named "led", they carry the LED related properties.
+
+- reg:
+ Usage: required
+ Value type: <u32>
+ Definition: specifies which of the four LEDs this node corresponds to
+
+- linux,default-trigger:
+ Usage: optional
+ Value type: <string>
+ Definition: specifies the default trigger for the LED, as described in
+ "leds/common.txt"
+
+- label:
+ Usage: required
+ Value type: <string>
+ Definition: specifies a name of this LED, as described in
+ "leds/common.txt"
+
+- led-max-microamp:
+ Usage: required
+ Value type: <u32>
+ Definition: specifies the max current for this LED, in uA, as described
+ in "leds/common.txt"
+
+- ti,pwm-zones:
+ Usage: optional
+ Value type: <u32 list>
+ Definition: lists the ALS zones to be PWM controlled for this LED, the
+ values in the list are in the range [0 - 4]
+
+= EXAMPLE
+
+i2c@12460000 {
+ compatible = "qcom,i2c-qup-v1.1.1";
+ ...
+
+ lm3533@36 {
+ compatible = "ti,lm3533";
+ reg = <0x36>;
+
+ ti,hwen-gpios = <&pm8921_gpio 26 GPIO_ACTIVE_HIGH>;
+ ti,als-supply = <&pm8921_l11>;
+
+ ti,boost-freq = <500000>;
+ ti,boost-ovp = <24>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ als {
+ ti,als-resistance = <200000>;
+ };
+
+ backlight@0 {
+ reg = <0>;
+ label = "backlight";
+
+ led-max-microamp = <20200>;
+ };
+
+ led@0 {
+ reg = <0>;
+ label = "red";
+
+ led-max-microamp = <5000>;
+ };
+
+ led@1 {
+ reg = <1>;
+ label = "green";
+
+ led-max-microamp = <5000>;
+ };
+
+ led@2 {
+ reg = <2>;
+ label = "blue";
+
+ led-max-microamp = <5000>;
+ };
+ };
+
--
2.4.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
