Re: [PATCH v4 4/4] ARM: dts: sun6i: Add dts file for MSI Primo81 tablet

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Fri, Oct 23, 2015 at 11:50:41AM +0800, Chen-Yu Tsai wrote:

> From: Karsten Merker <merker@xxxxxxxxxx>
> 
> The MSI Primo81 is an A31s based tablet, with 1G RAM, 16G NAND,
> 768x1024 IPS LCD display, mono speaker, 0.3 MP front camera, 2.0 MP
> rear camera, 3500 mAh battery, gt911 touchscreen, mma8452 accelerometer
> and rtl8188etv usb wifi. Has "power", "volume+" and "volume-" buttons
> (both volume buttons are also connected to the UBOOT_SEL pin). The

Hello Chen-Yu,

the volume button function is something that I wanted to confirm
again but forgot to ask previously: Siarhei had pointed out that
only the volume+ button triggers UBOOT_SEL, but for me actually
both volume buttons work as described above.  Could you
cross-check that on your Primo81?

> external connectors are represented by MicroSD slot, MiniHDMI, MicroUSB
> OTG and 3.5mm headphone jack.
> 
> USB OTG is enabled in host only mode. AXP221 USB power supply and
> GPIO support are required for full USB OTG support.
> 
> Signed-off-by: Siarhei Siamashka <siarhei.siamashka@xxxxxxxxx>
> Signed-off-by: Karsten Merker <merker@xxxxxxxxxx>
> Signed-off-by: Chen-Yu Tsai <wens@xxxxxxxx>
> ---
> 
> Changes since last submission (was part of Sinlinx SinA31s series)
> 
>   - Update axp22x.dtsi file name
>   - Sort regulators
>   - Drop URL in commit message
>   - Drop comment for capacitive touch panel
>   - Add simplefb regulators
>   - Drop regulator-always-on for regulators that aren't critical
>   - Fix CPU and GPU regulator supply mix-up
> 
> ---
>  arch/arm/boot/dts/Makefile               |   1 +
>  arch/arm/boot/dts/sun6i-a31s-primo81.dts | 255 +++++++++++++++++++++++++++++++
>  2 files changed, 256 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sun6i-a31s-primo81.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index c00b72e750ab..78ade1a5e886 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -612,6 +612,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \
>  	sun6i-a31-m9.dtb \
>  	sun6i-a31-mele-a1000g-quad.dtb \
>  	sun6i-a31s-cs908.dtb \
> +	sun6i-a31s-primo81.dtb \
>  	sun6i-a31s-sina31s.dtb \
>  	sun6i-a31s-sinovoip-bpi-m2.dtb \
>  	sun6i-a31s-yones-toptech-bs1078-v2.dtb
> diff --git a/arch/arm/boot/dts/sun6i-a31s-primo81.dts b/arch/arm/boot/dts/sun6i-a31s-primo81.dts
> new file mode 100644
> index 000000000000..2d4250b1faf8
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun6i-a31s-primo81.dts
> @@ -0,0 +1,255 @@
> +/*
> + * Copyright 2014 Siarhei Siamashka <siarhei.siamashka@xxxxxxxxx>
> + * Copyright 2015 Karsten Merker <merker@xxxxxxxxxx>
> + * Copyright 2015 Chen-Yu Tsai <wens@xxxxxxxx>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun6i-a31s.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> +	model = "MSI Primo81 tablet";
> +	compatible = "msi,primo81", "allwinner,sun6i-a31s";
> +};
> +
> +&cpu0 {
> +	cpu-supply = <&reg_dcdc3>;
> +};
> +
> +&ehci0 {
> +	/* rtl8188etv wifi is connected here */
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	/* pull-ups and device VDDIO use AXP221 DLDO3 */
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c0_pins_a>;
> +	status = "failed";
> +};
> +
> +&i2c1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c1_pins_a>;
> +	status = "okay";
> +
> +	ctp@5d {
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&gt911_int_primo81>;
> +		compatible = "goodix,gt911";
> +		reg = <0x5d>;
> +		interrupt-parent = <&pio>;
> +		interrupts = <0 3 IRQ_TYPE_LEVEL_HIGH>; /* PA3 */

I'd like to add a

		touchscreen-swapped-x-y = "true";

as described in
Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
here, as the display is in portrait mode while the touchscreen is
in landscape mode and needs to have the x and y axes swapped to
work in the same coordinate system as the display.

Regarding the driver side: the goodix driver in kernel 4.3
doesn't yet support this property, but patches to add support for
it are on the linux-input list and should hopefully make it into
kernel 4.4.

> +	};
> +};
> +
> +&i2c2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c2_pins_a>;
> +	status = "okay";
> +
> +	accelerometer@1c {
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&mma8452_int_primo81>;
> +		compatible = "fsl,mma8452";
> +		reg = <0x1c>;
> +		interrupt-parent = <&pio>;
> +		interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; /* PA9 */
> +		#io-channel-cells = <1>;
> +	};
> +};
> +
> +&lradc {
> +	vref-supply = <&reg_aldo3>;
> +	status = "okay";
> +
> +	button@158 {
> +		label = "Volume Up";
> +		linux,code = <KEY_VOLUMEUP>;
> +		channel = <0>;
> +		voltage = <158730>;
> +	};
> +
> +	button@349 {
> +		label = "Volume Down";
> +		linux,code = <KEY_VOLUMEDOWN>;
> +		channel = <0>;
> +		voltage = <349206>;
> +	};
> +};
> +
> +&mmc0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_primo81>;
> +	vmmc-supply = <&reg_dcdc1>;
> +	bus-width = <4>;
> +	cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
> +	cd-inverted;
> +	status = "okay";
> +};
> +
> +&pio {
> +	gt911_int_primo81: gt911_int_pin@0 {
> +		allwinner,pins = "PA3";
> +		allwinner,function = "gpio_in";
> +		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +	};
> +
> +	mma8452_int_primo81: mma8452_int_pin@0 {
> +		allwinner,pins = "PA9";
> +		allwinner,function = "gpio_in";
> +		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
> +	};
> +
> +	mmc0_cd_pin_primo81: mmc0_cd_pin@0 {
> +		allwinner,pins = "PA8";
> +		allwinner,function = "gpio_in";
> +		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
> +	};
> +};
> +
> +&p2wi {
> +	status = "okay";
> +
> +	axp22x: pmic@68 {
> +		compatible = "x-powers,axp221";
> +		reg = <0x68>;
> +		interrupt-parent = <&nmi_intc>;
> +		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> +	};
> +};
> +
> +#include "axp22x.dtsi"
> +
> +&reg_aldo3 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <2700000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-name = "avcc";
> +};
> +
> +&reg_dc1sw {
> +	regulator-min-microvolt = <3000000>;
> +	regulator-max-microvolt = <3000000>;
> +	regulator-name = "vcc-lcd";
> +};
> +
> +&reg_dc5ldo {
> +	regulator-min-microvolt = <700000>;
> +	regulator-max-microvolt = <1320000>;
> +	regulator-name = "vdd-cpus"; /* This is an educated guess */
> +};
> +
> +&reg_dcdc1 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <3000000>;
> +	regulator-max-microvolt = <3000000>;
> +	regulator-name = "vcc-3v0";
> +};
> +
> +&reg_dcdc2 {
> +	regulator-min-microvolt = <700000>;
> +	regulator-max-microvolt = <1320000>;
> +	regulator-name = "vdd-gpu";
> +};
> +
> +&reg_dcdc3 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <700000>;
> +	regulator-max-microvolt = <1320000>;
> +	regulator-name = "vdd-cpu";
> +};
> +
> +&reg_dcdc4 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <700000>;
> +	regulator-max-microvolt = <1320000>;
> +	regulator-name = "vdd-sys-dll";
> +};
> +
> +&reg_dcdc5 {
> +	regulator-always-on;
> +	regulator-min-microvolt = <1500000>;
> +	regulator-max-microvolt = <1500000>;
> +	regulator-name = "vcc-dram";
> +};
> +
> +&reg_dldo1 {
> +	regulator-min-microvolt = <3300000>;
> +	regulator-max-microvolt = <3300000>;
> +	regulator-name = "vcc-wifi";
> +};
> +
> +&reg_dldo3 {
> +	regulator-min-microvolt = <2800000>;
> +	regulator-max-microvolt = <2800000>;
> +	regulator-name = "vddio-csi";
> +};
> +
> +&reg_eldo3 {
> +	regulator-min-microvolt = <1080000>;
> +	regulator-max-microvolt = <1320000>;
> +	regulator-name = "vdd-mipi-bridge";
> +};
> +
> +&simplefb_lcd {
> +	vcc-lcd-supply = <&reg_dc1sw>;
> +	vdd-mipi-bridge-supply = <&reg_eldo3>;
> +};
> +
> +&usb_otg {
> +	/* otg support requires support for AXP221 usb-power-supply and GPIO */
> +	dr_mode = "host";
> +	status = "okay";
> +};
> +
> +&usbphy {
> +	usb1_vbus-supply = <&reg_dldo1>;
> +	status = "okay";
> +};
> -- 
> 2.6.1

Regards,
Karsten
-- 
Gem. Par. 28 Abs. 4 Bundesdatenschutzgesetz widerspreche ich der Nutzung
sowie der Weitergabe meiner personenbezogenen Daten für Zwecke der
Werbung sowie der Markt- oder Meinungsforschung.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux