Re: Which is better to specify console, "console= " or "stdout-path" ?

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi Peter,

2015-10-22 1:26 GMT+09:00 Peter Hurley <peter@xxxxxxxxxxxxxxxxxx>:
> On 10/21/2015 11:38 AM, Masahiro Yamada wrote:
>> Hi Peter.
>>
>> 2015-10-21 21:46 GMT+09:00 Peter Hurley <peter@xxxxxxxxxxxxxxxxxx>:
>>> On 10/21/2015 04:58 AM, Sudeep Holla wrote:
>>>> On 21/10/15 06:09, Masahiro Yamada wrote:
>>>>> I think there exist two ways to specify the console port and baudrate.
>>>>>
>>>>>
>>>>> [1] Specify console in bootargs
>>>>>
>>>>>    chosen {
>>>>>          bootargs = "console=ttyS0,115200";
>>>>>    };
>>>>>
>>>>>
>>>>> [2] Specify stdout-path
>>>>>
>>>>>     chosen {
>>>>>           stdout-path = "serial0:115200n8";
>>>>
>>>> This will work for even early/boot console, so this is better than
>>>> option [1]
>>>
>>> Be aware that options specified via /chosen/stdout-path are
>>> currently ignored by earlycon. There were some hiccups getting the
>>> initial support upstream; when 4.4 hits mainline, I'll resubmit
>>> my series that implements the of_serial i/o properties and
>>> options passthrough to earlycon setup.
>>
>>
>> As I said in another thread ("serial: earlycon: allow to specify
>> uartclk in earlycon kernel-parameter"),
>> stdout-path can pass dev->baud, but not port->uartclk.
>
> That's true but I'm not seeing in that thread where you wrote that?

Sorry, I made you confused.  I was talking about the kernel parameter (console=)
in the thread.

> My replies there were specific to uartclk on the kernel command line,
> which isn't necessary if the bootloader has already initialized the
> uart.
>
>> It is usually specified "clocks" phandle, but
>> clk is not ready at the point of earlycon.
>>
>> It seems impossible to set up the baudrate even if the options are passed.
>
> It's difficult to understand what you're trying to do when I can't
> see the code you're referring to.  For example, I only recently
> understood that you're talking about a earlycon implementation
> that you're working on and not the 8250 earlycon itself.

Sorry again for making you confused.

I was talking both.

Now I am tackling on some ARM board porting.


The board has a pure 8250 family device (compatible = "ns16550a") on it.

In addition, there exist 8250-variant IPs inside the SoC.
(this is similar to 8250, but slightly different.
drivers/tty/serial/8250/8250_uniphier.c)


What I want to do is:
  [1] To use  drivers/tty/serial/8250/8250_early.c  for the on-board ns16550a.
  [2] To implement my own EARLYCON_DECLARE() in
drivers/tty/serial/8250/8250_uniphier.c



> If you look at other non-8250 earlycons, you'll see they all ignore
> the baud rate, on the assumption the bootloader already set it up.

OK, I will do so for [2].


> The 8250 earlycon is a little different because legacy platforms
> do not initialize the uart.


Make sense.

For legacy platforms, earlycon initializes the uart,
assuming the hard-coded "port->uartclk = BASE_BAUD * 16"
is the value.


For embedded boards such as ARM, the boot-loader should initialize the UART
and the earlycon should preserve it because port->uartclk varies from
board to board.
(For example, the ns16550a on my board expects   BASE_BAUD is 1228000,
but it does not match the one in include/asm-generic/serial.h )


-- 
Best Regards
Masahiro Yamada
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux