ChangeLog
v6:
- add new patch which tries to read the JEDEC ID with different SPI protocols
and different commands: 0x9f (SPI-1-1-1), 0xaf (SPI-4-4-4) and finally
0xaf (SPI-2-2-2).
- remove the set_protocol() hook from struct spi_nor and add 4 new members
instead of type enum spi_protocol:
read_proto, write_proto, erase_proto, reg_proto.
The relevant protocol value should be checked by the driver specific read(),
write(), erase(), read_reg() and write_reg() hook implementations.
- remove unused hooks: write_xfer() and read_xfer().
- tune the op code for read, write and erase commands depending on the memory
manufacturer.
- remove some previously added "Acked-by" since the protocol switch strategy
has been changed but not discussed yet.
v5:
- remove unused inline functions qspi_read[bw]() and qspi_write[bw](),
keep only qspi_readl() and qspi_writel().
- use reinit_completion() instead of init_completion() during run time,
call init_completion() once for all in the probe().
- add a dev_warn() when trying to tune the number of dummy cycles for
spi-nor of a not supported manufacturer then fall back to the default
framework value.
- reword some comments.
- add "Acked-by: Marek Vasut <marex@xxxxxxx>" for patches 1 and 4.
- add "Acked-by: Bean Huo <beanhuo@xxxxxxxxxx>" for patch 1.
v4:
- add "OF && HAS_DMA" dependency in Kconfig for Atmel Quad SPI driver.
- return -ENOMEM instead of the return code of dma_mapping_error() as this
function returns a boolean on ARM achitecture.
- add "Acked-by: Nicolas Ferre <nicolas.ferre@xxxxxxxxx>" for Atmel Quad
SPI driver and its DT binding documentation.
v3:
- reword the comment which explains that spi_nor_set_protocol() is used by
the spi-nor framework to notify lower layers, especially the (Q)SPI
controller about a protocol change.
- change the definitions of register/bitfield macros in the Atmel QSPI
controller driver: get rid of concatenation operator and use BIT and
GENMASK macros when possible.
- use #define[SPACE] instead of #define[TAB]
v2:
- remove the patches to set the "latency code" of Spansion QSPI memories
(support of Spansion memories may be submitted in later series).
- rename "qspi" node into "spi" in the DT example to fit ePAPR standard.
- remove the useless "qspi0" label from the DT node example.
- remove the leading 0 from the size of the second memory region to make
it consistent with the size of the first memory region.
- indent the DT bindings documentation to make it more readable.
- remove the useless ".bus = &platform_bus_type," line from the
platform driver definition.
v1:
This series of patches add support for the new Atmel QSPI controller
embedded inside sama5d2x SoCs.
These patches were first developped for linux-3.18-at91 and tested on a
sama5d27 Xplained ultra board, which embeds a Micron n25q128a13 QSPI NOR
flash memory. Then the series was adapted for mainline.
Cyrille Pitchen (8):
mtd: spi-nor: read JEDEC ID with multiple I/O protocols
mtd: spi-nor: remove unused read_xfer/write_xfer hooks
mtd: spi-nor: update the SPI protocol when enabling manufacturer Quad
mode
mtd: spi-nor: use optimized commands for read/write/erase operations
Documentation: mtd: add a DT property to set the number of dummy
cycles
mtd: spi-nor: allow to tune the number of dummy cycles
Documentation: atmel-quadspi: add binding file for Atmel QSPI driver
mtd: atmel-quadspi: add driver for Atmel QSPI controller
.../devicetree/bindings/mtd/atmel-quadspi.txt | 29 +
.../devicetree/bindings/mtd/jedec,spi-nor.txt | 6 +
drivers/mtd/spi-nor/Kconfig | 7 +
drivers/mtd/spi-nor/Makefile | 1 +
drivers/mtd/spi-nor/atmel-quadspi.c | 889 +++++++++++++++++++++
drivers/mtd/spi-nor/spi-nor.c | 356 +++++++--
include/linux/mtd/spi-nor.h | 63 +-
7 files changed, 1269 insertions(+), 82 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mtd/atmel-quadspi.txt
create mode 100644 drivers/mtd/spi-nor/atmel-quadspi.c
--
1.8.2.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
