[PATCH v2 8/9] ARM: dts: imx: add Boundary Devices Nitrogen6_Max board

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Based on i.MX6 Quad with 4GB of DDR3.

http://boundarydevices.com/product/nitrogen6max/

Signed-off-by: Gary Bisson <gary.bisson@xxxxxxxxxxxxxxxxxxx>
---
 arch/arm/boot/dts/Makefile                   |   1 +
 arch/arm/boot/dts/imx6q-nitrogen6_max.dts    |  53 ++
 arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi | 873 +++++++++++++++++++++++++++
 3 files changed, 927 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-nitrogen6_max.dts
 create mode 100644 arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 233159d..cc29515 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -313,6 +313,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-gw552x.dtb \
 	imx6q-hummingboard.dtb \
 	imx6q-nitrogen6x.dtb \
+	imx6q-nitrogen6_max.dtb \
 	imx6q-phytec-pbab01.dtb \
 	imx6q-rex-pro.dtb \
 	imx6q-sabreauto.dtb \
diff --git a/arch/arm/boot/dts/imx6q-nitrogen6_max.dts b/arch/arm/boot/dts/imx6q-nitrogen6_max.dts
new file mode 100644
index 0000000..d417457
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-nitrogen6_max.dts
@@ -0,0 +1,53 @@
+/*
+ * Copyright 2015 Boundary Devices, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-nitrogen6_max.dtsi"
+
+/ {
+	model = "Boundary Devices i.MX6 Quad Nitrogen6_MAX Board";
+	compatible = "boundary,imx6q-nitrogen6_max", "fsl,imx6q";
+};
+
+&sata {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi b/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
new file mode 100644
index 0000000..6f4917b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
@@ -0,0 +1,873 @@
+/*
+ * Copyright 2015 Boundary Devices, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	memory {
+		reg = <0x10000000 0xF0000000>;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_1p8v: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "1P8V";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		reg_2p5v: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "2P5V";
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <2500000>;
+			regulator-always-on;
+		};
+
+		reg_3p3v: regulator@2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "3P3V";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		reg_usb_otg_vbus: regulator@3 {
+			compatible = "regulator-fixed";
+			reg = <3>;
+			regulator-name = "usb_otg_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_usb_h1_vbus: regulator@4 {
+			compatible = "regulator-fixed";
+			reg = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usbh1>;
+			regulator-name = "usb_h1_vbus";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+
+		reg_wlan_vmmc: regulator@5 {
+			compatible = "regulator-fixed";
+			reg = <5>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_wlan_vmmc>;
+			regulator-name = "reg_wlan_vmmc";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+			startup-delay-us = <70000>;
+			enable-active-high;
+		};
+
+		reg_can_xcvr: regulator@6 {
+			compatible = "regulator-fixed";
+			reg = <6>;
+			regulator-name = "CAN XCVR";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_can_xcvr>;
+			gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		power {
+			label = "Power Button";
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			gpio-key,wakeup;
+		};
+
+		menu {
+			label = "Menu";
+			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_MENU>;
+		};
+
+		home {
+			label = "Home";
+			gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+		};
+
+		back {
+			label = "Back";
+			gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_BACK>;
+		};
+
+		volume-up {
+			label = "Volume Up";
+			gpios = <&gpio7 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		volume-down {
+			label = "Volume Down";
+			gpios = <&gpio7 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	i2cmux@2 {
+		compatible = "i2c-mux-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c2mux>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-gpios = <&gpio3 20 GPIO_ACTIVE_HIGH
+			     &gpio4 15 GPIO_ACTIVE_HIGH>;
+		i2c-parent = <&i2c2>;
+		idle-state = <0>;
+
+		i2c2@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2cmux@3 {
+		compatible = "i2c-mux-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c3mux>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>;
+		i2c-parent = <&i2c3>;
+		idle-state = <0>;
+
+		i2c3@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		speaker-enable {
+			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+			retain-state-suspended;
+			default-state = "off";
+		};
+
+		ttymxc4-rs232 {
+			gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>;
+			retain-state-suspended;
+			default-state = "on";
+		};
+	};
+
+	backlight_lcd: backlight_lcd {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_3p3v>;
+		status = "okay";
+	};
+
+	backlight_lvds0: backlight_lvds0 {
+		compatible = "pwm-backlight";
+		pwms = <&pwm4 0 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_3p3v>;
+		status = "okay";
+	};
+
+	backlight_lvds1: backlight_lvds1 {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 0 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_3p3v>;
+		status = "okay";
+	};
+
+	lcd_display: display@di0 {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "bgr666";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_j15>;
+		status = "okay";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel_lcd {
+		compatible = "okaya,rs800480t-7x0gp";
+		backlight = <&backlight_lcd>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	panel_lvds0 {
+		compatible = "hannstar,hsd100pxn1";
+		backlight = <&backlight_lvds0>;
+
+		port {
+			panel_in_lvds0: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	panel_lvds1 {
+		compatible = "hannstar,hsd100pxn1";
+		backlight = <&backlight_lvds1>;
+
+		port {
+			panel_in_lvds1: endpoint {
+				remote-endpoint = <&lvds1_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx6q-nitrogen6_max-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx6q-nitrogen6_max-sgtl5000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sgtl5000>;
+		ssi-controller = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <3>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_can_xcvr>;
+	status = "okay";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&ecspi1 {
+	fsl,spi-num-chipselects = <1>;
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash: m25p80@0 {
+		compatible = "microchip,sst25vf016b";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	txen-skew-ps = <0>;
+	txc-skew-ps = <3000>;
+	rxdv-skew-ps = <0>;
+	rxc-skew-ps = <3000>;
+	rxd0-skew-ps = <0>;
+	rxd1-skew-ps = <0>;
+	rxd2-skew-ps = <0>;
+	rxd3-skew-ps = <0>;
+	txd0-skew-ps = <0>;
+	txd1-skew-ps = <0>;
+	txd2-skew-ps = <0>;
+	txd3-skew-ps = <0>;
+	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	codec: sgtl5000@0a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		clocks = <&clks 201>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_3p3v>;
+	};
+
+	rtc: rtc@68 {
+		compatible = "st,rv4162";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rv4162>;
+		reg = <0x68>;
+		interrupts-extended = <&gpio4 6 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	egalax_ts@04 {
+		compatible = "eeti,egalax_ts";
+		reg = <0x04>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+	};
+
+	ft5x06_ts@38 {
+		compatible = "edt,edt-ft5x06";
+		reg = <0x38>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&iomuxc {
+	imx6q-nitrogen6_max {
+		pinctrl_audmux: audmuxgrp {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+				MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+				MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+				MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+			>;
+		};
+
+		pinctrl_can1: can1grp {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
+				MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b0
+			>;
+		};
+
+		pinctrl_can_xcvr: can-xcvrgrp {
+			fsl,pins = <
+				/* Flexcan XCVR enable */
+				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+			>;
+		};
+
+		pinctrl_ecspi1: ecspi1grp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+				MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+				MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+				MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x000b1
+			>;
+		};
+
+		pinctrl_enet: enetgrp {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
+				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
+				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x100b0
+				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x100b0
+				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x100b0
+				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x100b0
+				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x100b0
+				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x100b0
+				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
+				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+				/* Phy reset */
+				MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x0f0b0
+				MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28	0x1b0b0
+				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
+			>;
+		};
+
+		pinctrl_gpio_keys: gpio_keysgrp {
+			fsl,pins = <
+				/* Power Button */
+				MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0
+				/* Menu Button */
+				MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
+				/* Home Button */
+				MX6QDL_PAD_NANDF_D4__GPIO2_IO04		0x1b0b0
+				/* Back Button */
+				MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x1b0b0
+				/* Volume Up Button */
+				MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b0
+				/* Volume Down Button */
+				MX6QDL_PAD_SD3_DAT4__GPIO7_IO01		0x1b0b0
+			>;
+		};
+
+		pinctrl_i2c1: i2c1grp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D21__I2C1_SCL	0x4001b8b1
+				MX6QDL_PAD_EIM_D28__I2C1_SDA	0x4001b8b1
+			>;
+		};
+
+		pinctrl_i2c2: i2c2grp {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b8b1
+				MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b8b1
+			>;
+		};
+
+		pinctrl_i2c2mux: i2c2muxgrp {
+			fsl,pins = <
+				/* ov5642 camera i2c enable */
+				MX6QDL_PAD_EIM_D20__GPIO3_IO20	0x000b0
+				/* ov5640_mipi camera i2c enable */
+				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15	0x000b0
+			>;
+		};
+
+		pinctrl_i2c3: i2c3grp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_5__I2C3_SCL	0x4001b8b1
+				MX6QDL_PAD_GPIO_16__I2C3_SDA	0x4001b8b1
+			>;
+		};
+
+		pinctrl_i2c3mux: i2c3muxgrp {
+			fsl,pins = <
+				/* PCIe I2C enable */
+				MX6QDL_PAD_EIM_OE__GPIO2_IO25	0x000b0
+			>;
+		};
+
+		pinctrl_j15: j15grp {
+			fsl,pins = <
+				MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+				MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15       0x10
+				MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02        0x10
+				MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03        0x10
+				MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00   0x10
+				MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01   0x10
+				MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02   0x10
+				MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03   0x10
+				MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04   0x10
+				MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05   0x10
+				MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06   0x10
+				MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07   0x10
+				MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08   0x10
+				MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09   0x10
+				MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10  0x10
+				MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11  0x10
+				MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12  0x10
+				MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13  0x10
+				MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14  0x10
+				MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15  0x10
+				MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16  0x10
+				MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17  0x10
+				MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18  0x10
+				MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19  0x10
+				MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20  0x10
+				MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21  0x10
+				MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22  0x10
+				MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23  0x10
+			>;
+		};
+
+		pinctrl_pcie: pciegrp {
+			fsl,pins = <
+				/* PCIe reset */
+				MX6QDL_PAD_EIM_BCLK__GPIO6_IO31	0x000b0
+			>;
+		};
+
+		pinctrl_pwm1: pwm1grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT3__PWM1_OUT	0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm2: pwm2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT2__PWM2_OUT	0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm3: pwm3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_DAT1__PWM3_OUT	0x1b0b1
+			>;
+		};
+
+		pinctrl_pwm4: pwm4grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD1_CMD__PWM4_OUT	0x1b0b1
+			>;
+		};
+
+		pinctrl_rv4162: rv4162grp {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_COL0__GPIO4_IO06	0x1b0b0
+			>;
+		};
+
+		pinctrl_sgtl5000: sgtl5000grp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x000b0
+				MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1b0b0
+				MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x1b0b0
+			>;
+		};
+
+		pinctrl_uart1: uart1grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
+				MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
+			>;
+		};
+
+		pinctrl_uart2: uart2grp {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+				MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+			>;
+		};
+
+		pinctrl_uart5: uart5grp {
+			fsl,pins = <
+				MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA	0x130b1
+				MX6QDL_PAD_KEY_COL1__UART5_TX_DATA	0x030b1
+				/* RS485 RX Enable: pull up */
+				MX6QDL_PAD_NANDF_RB0__GPIO6_IO10	0x1b0b1
+				/* RS485 DEN: pull down */
+				MX6QDL_PAD_NANDF_CLE__GPIO6_IO07	0x030b1
+				/* RS485/!RS232 Select: pull down (rs232) */
+				MX6QDL_PAD_EIM_CS1__GPIO2_IO24		0x030b1
+				/* ON: pull down */
+				MX6QDL_PAD_NANDF_ALE__GPIO6_IO08	0x030b1
+			>;
+		};
+
+		pinctrl_usbh1: usbh1grp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x0b0b0
+			>;
+		};
+
+		pinctrl_usbotg: usbotggrp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+				MX6QDL_PAD_KEY_COL4__USB_OTG_OC		0x1b0b0
+				/* power enable, high active */
+				MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x000b0
+			>;
+		};
+
+		pinctrl_usdhc2: usdhc2grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			>;
+		};
+
+		pinctrl_usdhc3: usdhc3grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+				MX6QDL_PAD_NANDF_CS1__SD3_VSELECT	0x100b0
+				MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0
+			>;
+		};
+
+		pinctrl_usdhc4: usdhc4grp {
+			fsl,pins = <
+				MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+				MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+				MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+				MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+				MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+				MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+				MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
+				MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
+				MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
+				MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
+			>;
+		};
+
+		pinctrl_wlan_vmmc: wlan_vmmcgrp {
+			fsl,pins = <
+				MX6QDL_PAD_NANDF_CS0__GPIO6_IO11	0x100b0
+				MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x000b0
+				MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x000b0
+				MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT	0x000b0
+			>;
+		};
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <18>;
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in_lvds0>;
+			};
+		};
+	};
+
+	lvds-channel@1 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <18>;
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds1_out: endpoint {
+				remote-endpoint = <&panel_in_lvds1>;
+			};
+		};
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio6 31 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	non-removable;
+	vmmc-supply = <&reg_wlan_vmmc>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1271";
+		reg = <2>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+		ref-clock-frequency = <38400000>;
+	};
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <8>;
+	non-removable;
+	vmmc-supply = <&reg_1p8v>;
+	keep-power-in-suspend;
+	status = "okay";
+};
-- 
2.5.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux