On 28.08.2015 10:48, Jaehoon Chung wrote:
> On 08/27/2015 09:26 PM, Krzysztof Kozlowski wrote:
>> W dniu 27.08.2015 o 18:29, Jaehoon Chung pisze:
>>> Currently vmmc's property is wrong.
>>> If it needs to control two supplies, then it has to use vmmc/vqmmc-supply.
>>> (Card supply power and I/O Line supply Power.)
>>>
>>> Signed-off-by: Jaehoon Chung <jh80.chung@xxxxxxxxxxx>
>>> ---
>>> arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 7 ++++---
>>> 1 file changed, 4 insertions(+), 3 deletions(-)
>>>
>>> diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
>>> index ca7d168..4ddabfd 100644
>>> --- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
>>> +++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
>>> @@ -461,10 +461,10 @@
>>> &mshc_0 {
>>> pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
>>> pinctrl-names = "default";
>>> - vmmc-supply = <&ldo20_reg &buck8_reg>;
>>> + vmmc-supply = <&ldo20_reg>;
>>> + vqmmc-supply = <&buck8_reg>;
>>
>> Shouldn't this be reversed? LDO20 has 1.8V and it goes to MMC connector,
>> so it should be VQMMC?
>
> If my schematics is right thing, buck8 is used LAN card power.
> I will send after removing buck8_reg. how about?
> Anyway, Thanks for pointing out. :)
Removing this regulator from this node would effectively disable it.
That could affect other components like LAN.
Anyway before fixing the order I would prefer to find the right
regulators used by MSHC node.
Best regards,
Krzysztof
>
> I don't know who this regulator applied. I have guessed that it used for eMMC.
> Sorry for guessing.
>
> Best Regards,
> Jaehoon Chung
>
>>
>> In the same time I can't find on schematics where BUCK8 goes...
>>
>> The SDHCI_2 node below looks good.
>>
>> Best regards,
>> Krzysztof
>>
>>> mmc-pwrseq = <&emmc_pwrseq>;
>>> status = "okay";
>>> -
>>> num-slots = <1>;
>>> broken-cd;
>>> card-detect-delay = <200>;
>>> @@ -485,7 +485,8 @@
>>> bus-width = <4>;
>>> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
>>> pinctrl-names = "default";
>>> - vmmc-supply = <&ldo4_reg &ldo21_reg>;
>>> + vmmc-supply = <&ldo21_reg>;
>>> + vqmmc-supply = <&ldo4_reg>;
>>> cd-gpios = <&gpk2 2 0>;
>>> cd-inverted;
>>> status = "okay";
>>>
>>
>>
>>
>
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
