Re: [PATCH v3 06/14] Documentation: drm/bridge: add document for analogix_dp

[Yakir Yang <ykk@xxxxxxxxxxxxxx>]

Hi Rob,

在 08/23/2015 06:23 PM, Rob Herring 写道:
> On Wed, Aug 19, 2015 at 9:50 AM, Yakir Yang <ykk@xxxxxxxxxxxxxx> wrote:
> > Analogix dp driver is split from exynos dp driver, so we just
> > make an copy of exynos_dp.txt, and then simplify exynos_dp.txt
> >
> > Beside update some exynos dtsi file with the latest change
> > according to the devicetree binding documents.
> You can't just change the exynos bindings and break compatibility. Is
> there some agreement with exynos folks to do this?

Yeah, this change only start to introduce in version 3 series, so there is
no agreement or discuss before.

> > Signed-off-by: Yakir Yang <ykk@xxxxxxxxxxxxxx>
> > ---
> > Changes in v3:
> > - Take Heiko suggest, add devicetree binding documents.
> > - Take Thierry Reding suggest, remove sync pol & colorimetry properies
> >    from the new analogix dp driver devicetree binding.
> > - Update the exist exynos dtsi file with the latest DP DT properies.
> >
> > Changes in v2: None
> >
> >   .../devicetree/bindings/drm/bridge/analogix_dp.txt | 70 ++++++++++++++++++++++
> >   .../devicetree/bindings/video/exynos_dp.txt        | 50 ++++++----------
> >   arch/arm/boot/dts/exynos5250-arndale.dts           | 10 ++--
> >   arch/arm/boot/dts/exynos5250-smdk5250.dts          | 10 ++--
> >   arch/arm/boot/dts/exynos5250-snow.dts              | 12 ++--
> >   arch/arm/boot/dts/exynos5250-spring.dts            | 12 ++--
> >   arch/arm/boot/dts/exynos5420-peach-pit.dts         | 12 ++--
> >   arch/arm/boot/dts/exynos5420-smdk5420.dts          | 10 ++--
> >   arch/arm/boot/dts/exynos5800-peach-pi.dts          | 12 ++--
> >   9 files changed, 119 insertions(+), 79 deletions(-)
> >   create mode 100644 Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt
> >
> > diff --git a/Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt b/Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt
> > new file mode 100644
> > index 0000000..6127018
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt
> > @@ -0,0 +1,70 @@
> > +Analogix Display Port bridge bindings
> > +
> > +Required properties for dp-controller:
> > +       -compatible:
> > +               platform specific such as:
> > +                * "samsung,exynos5-dp"
> > +                * "rockchip,rk3288-dp"
> > +       -reg:
> > +               physical base address of the controller and length
> > +               of memory mapped region.
> > +       -interrupts:
> > +               interrupt combiner values.
> > +       -clocks:
> > +               from common clock binding: handle to dp clock.
> > +       -clock-names:
> > +               from common clock binding: Shall be "dp".
> > +       -interrupt-parent:
> > +               phandle to Interrupt combiner node.
> > +       -phys:
> > +               from general PHY binding: the phandle for the PHY device.
> > +       -phy-names:
> > +               from general PHY binding: Should be "dp".
> > +       -analogix,color-space:
> > +               input video data format.
> > +                       COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2
> > +       -analogix,color-depth:
> > +               number of bits per colour component.
> > +                       COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3
> This seems pretty generic. Just use 6, 8, 10, or 12 for values. And
> drop the vendor prefix.

Okay, thanks


> > +       -analogix,link-rate:
> > +               max link rate supported by the eDP controller.
> > +                       LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A,
> > +                       LINK_RATE_5_40GBPS = 0x14
> Same here. I'd rather see something like "link-rate-mbps" and use the
> actual rate.

Like "link-rate-mbps = 162000", so I need of_property_read_u32() for 
this prop.

Okay, done.

> > +       -analogix,lane-count:
> > +               max number of lanes supported by the eDP contoller.
> > +                       LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4
> And drop the vendor prefix here.

Done

> > +       -port@[X]: SoC specific port nodes with endpoint definitions as defined
> > +               in Documentation/devicetree/bindings/media/video-interfaces.txt,
> > +               please refer to the SoC specific binding document:
> > +               * Documentation/devicetree/bindings/video/exynos_dp.txt
> > +               * Documentation/devicetree/bindings/video/analogix_dp-rockchip.txt
> > +
> > +Optional properties for dp-controller:
> > +       -analogix,hpd-gpio:
> > +               Hotplug detect GPIO.
> > +                       Indicates which GPIO should be used for hotplug
> > +                       detection
> We should align with "hpd-gpios" used by HDMI connector binding. Or do
> we need a DP connector binding that this should be defined in?
> Probably so.
>
> The DRM related bindings are such a cluster f*ck with everyone picking
> their own way to do things. Just grep hpd in bindings for starters.
> That is just the tip.

Hmm... I don't understand how the HDMI connector binding works, there are no
driver that name with "hdmi-connector" compatible, does it just an 
sample case
for all HDMI dts node?

But I'm okay with your suggest here, change "analogix,hpd-gpio" to 
"hpd-gpios"  ;)

> > +       -video interfaces: Device node can contain video interface port
> > +                           nodes according to [1].
> Isn't this the same as ports above? How are they optional? 0 ports
> would be pretty useless.

I though I make an mistaken here, "-video interfaces" is the same as 
previous "ports".

And "ports" is an required property in rockchip case, cause we use it to 
bind "dp" driver
to crtc "vop" driver. But I thinks "ports" in not an required property 
in exynos case, they
only use when there are a dp/lvds application scenarios.

Here are example (./arch/arm/boot/dts/exynos5420-peach-pit.dts):
    &dp {
            [...]
            ports {
                    port@0 {
                            dp_out: endpoint {
                                    remote-endpoint = <&bridge_in>;
                            };
                    };
            };
    };

    ps8625: lvds-bridge@48 {
                [...]
                ports {
                        port@0 {
                                bridge_out: endpoint {
                                        remote-endpoint = <&panel_in>;
                                };
                        };

                        port@1 {
                                bridge_in: endpoint {
                                        remote-endpoint = <&dp_out>;
                                };
                        };
                };

        };

So I would rather to remove "ports" to analogix_dp-rockchip.txt with 
"required" flag,
and keep "video-port" in analogox-dp.txt with "optional" flag.

> > +
> > +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
> > +-------------------------------------------------------------------------------
> > +
> > +Example:
> > +
> > +       dp-controller {
> > +               compatible = "samsung,exynos5-dp";
> > +               reg = <0x145b0000 0x10000>;
> > +               interrupts = <10 3>;
> > +               interrupt-parent = <&combiner>;
> > +               clocks = <&clock 342>;
> > +               clock-names = "dp";
> > +
> > +               phys = <&dp_phy>;
> > +               phy-names = "dp";
> > +
> > +               analogix,color-space = <0>;
> > +               analogix,color-depth = <1>;
> > +               analogix,link-rate = <0x0a>;
> > +               analogix,lane-count = <4>;
> > +       };
> > diff --git a/Documentation/devicetree/bindings/video/exynos_dp.txt b/Documentation/devicetree/bindings/video/exynos_dp.txt
> > index 7a3a9cd..177506f 100644
> > --- a/Documentation/devicetree/bindings/video/exynos_dp.txt
> > +++ b/Documentation/devicetree/bindings/video/exynos_dp.txt
> > @@ -31,28 +31,10 @@ Required properties for dp-controller:
> >                  from general PHY binding: the phandle for the PHY device.
> >          -phy-names:
> >                  from general PHY binding: Should be "dp".
> > -       -samsung,color-space:
> > -               input video data format.
> > -                       COLOR_RGB = 0, COLOR_YCBCR422 = 1, COLOR_YCBCR444 = 2
> > -       -samsung,dynamic-range:
> > -               dynamic range for input video data.
> > -                       VESA = 0, CEA = 1
> > -       -samsung,ycbcr-coeff:
> > -               YCbCr co-efficients for input video.
> > -                       COLOR_YCBCR601 = 0, COLOR_YCBCR709 = 1
> > -       -samsung,color-depth:
> > -               number of bits per colour component.
> > -                       COLOR_6 = 0, COLOR_8 = 1, COLOR_10 = 2, COLOR_12 = 3
> > -       -samsung,link-rate:
> > -               link rate supported by the panel.
> > -                       LINK_RATE_1_62GBPS = 0x6, LINK_RATE_2_70GBPS = 0x0A
> > -       -samsung,lane-count:
> > -               number of lanes supported by the panel.
> > -                       LANE_COUNT1 = 1, LANE_COUNT2 = 2, LANE_COUNT4 = 4
> > -       - display-timings: timings for the connected panel as described by
> > -               Documentation/devicetree/bindings/video/display-timing.txt
> >
> >   Optional properties for dp-controller:
> > +       - display-timings: timings for the connected panel as described by
> > +               Documentation/devicetree/bindings/video/display-timing.txt
> >          -interlaced:
> >                  interlace scan mode.
> >                          Progressive if defined, Interlaced if not defined
> > @@ -62,14 +44,18 @@ Optional properties for dp-controller:
> >          -hsync-active-high:
> >                  HSYNC polarity configuration.
> >                          High if defined, Low if not defined
> > -       -samsung,hpd-gpio:
> > -               Hotplug detect GPIO.
> > -                       Indicates which GPIO should be used for hotplug
> > -                       detection
> > -       -video interfaces: Device node can contain video interface port
> > -                           nodes according to [1].
> >
> > -[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
> > +For the below properties, please refer to Analogix DP binding document:
> > + * Documentation/devicetree/bindings/drm/bridge/analogix_dp.txt
> > +       -phys (required)
> > +       -phy-names (required)
> > +       -analogix,color-space (required)
> > +       -analogix,color-depth (required)
> > +       -analogix,link-rate (required)
> > +       -analogix,lane-count (required)
> > +       -analogix,hpd-gpio (optional)
> > +       -video interfaces (optional)
> > +-------------------------------------------------------------------------------
> >
> >   Example:
> >
> > @@ -88,12 +74,10 @@ SOC specific portion:
> >
> >   Board Specific portion:
> >          dp-controller {
> > -               samsung,color-space = <0>;
> > -               samsung,dynamic-range = <0>;
> > -               samsung,ycbcr-coeff = <0>;
> > -               samsung,color-depth = <1>;
> > -               samsung,link-rate = <0x0a>;
> > -               samsung,lane-count = <4>;
> > +               analogix,color-space = <0>;
> > +               analogix,color-depth = <1>;
> > +               analogix,link-rate = <0x0a>;
> > +               analogix,lane-count = <4>;
> >
> >                  display-timings {
> >                          native-mode = <&lcd_timing>;
> > diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
> > index 7e728a1..e48798d 100644
> > --- a/arch/arm/boot/dts/exynos5250-arndale.dts
> > +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
> > @@ -119,12 +119,10 @@
> >
> >   &dp {
> >          status = "okay";
> > -       samsung,color-space = <0>;
> > -       samsung,dynamic-range = <0>;
> > -       samsung,ycbcr-coeff = <0>;
> > -       samsung,color-depth = <1>;
> > -       samsung,link-rate = <0x0a>;
> > -       samsung,lane-count = <4>;
> > +       analogix,color-space = <0>;
> > +       analogix,color-depth = <1>;
> > +       analogix,link-rate = <0x0a>;
> > +       analogix,lane-count = <4>;
> >   };
> >
> >   &fimd {
> > diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts
> > index 4fe186d..b8c6b8b 100644
> > --- a/arch/arm/boot/dts/exynos5250-smdk5250.dts
> > +++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts
> > @@ -75,12 +75,10 @@
> >   };
> >
> >   &dp {
> > -       samsung,color-space = <0>;
> > -       samsung,dynamic-range = <0>;
> > -       samsung,ycbcr-coeff = <0>;
> > -       samsung,color-depth = <1>;
> > -       samsung,link-rate = <0x0a>;
> > -       samsung,lane-count = <4>;
> > +       analogix,color-space = <0>;
> > +       analogix,color-depth = <1>;
> > +       analogix,link-rate = <0x0a>;
> > +       analogix,lane-count = <4>;
> >
> >          pinctrl-names = "default";
> >          pinctrl-0 = <&dp_hpd>;
> > diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
> > index b7f4122..9ce2b89 100644
> > --- a/arch/arm/boot/dts/exynos5250-snow.dts
> > +++ b/arch/arm/boot/dts/exynos5250-snow.dts
> > @@ -239,13 +239,11 @@
> >          status = "okay";
> >          pinctrl-names = "default";
> >          pinctrl-0 = <&dp_hpd>;
> > -       samsung,color-space = <0>;
> > -       samsung,dynamic-range = <0>;
> > -       samsung,ycbcr-coeff = <0>;
> > -       samsung,color-depth = <1>;
> > -       samsung,link-rate = <0x0a>;
> > -       samsung,lane-count = <2>;
> > -       samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>;
> > +       analogix,color-space = <0>;
> > +       analogix,color-depth = <1>;
> > +       analogix,link-rate = <0x0a>;
> > +       analogix,lane-count = <2>;
> > +       analogix,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>;
> >
> >          ports {
> >                  port@0 {
> > diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
> > index d03f9b8..9288ae6 100644
> > --- a/arch/arm/boot/dts/exynos5250-spring.dts
> > +++ b/arch/arm/boot/dts/exynos5250-spring.dts
> > @@ -69,13 +69,11 @@
> >          status = "okay";
> >          pinctrl-names = "default";
> >          pinctrl-0 = <&dp_hpd_gpio>;
> > -       samsung,color-space = <0>;
> > -       samsung,dynamic-range = <0>;
> > -       samsung,ycbcr-coeff = <0>;
> > -       samsung,color-depth = <1>;
> > -       samsung,link-rate = <0x0a>;
> > -       samsung,lane-count = <1>;
> > -       samsung,hpd-gpio = <&gpc3 0 GPIO_ACTIVE_HIGH>;
> > +       analogix,color-space = <0>;
> > +       analogix,color-depth = <1>;
> > +       analogix,link-rate = <0x0a>;
> > +       analogix,lane-count = <1>;
> > +       analogix,hpd-gpio = <&gpc3 0 GPIO_ACTIVE_HIGH>;
> >   };
> >
> >   &ehci {
> > diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
> > index 8f4d76c..695a380 100644
> > --- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
> > +++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
> > @@ -147,13 +147,11 @@
> >          status = "okay";
> >          pinctrl-names = "default";
> >          pinctrl-0 = <&dp_hpd_gpio>;
> > -       samsung,color-space = <0>;
> > -       samsung,dynamic-range = <0>;
> > -       samsung,ycbcr-coeff = <0>;
> > -       samsung,color-depth = <1>;
> > -       samsung,link-rate = <0x06>;
> > -       samsung,lane-count = <2>;
> > -       samsung,hpd-gpio = <&gpx2 6 0>;
> > +       analogix,color-space = <0>;
> > +       analogix,color-depth = <1>;
> > +       analogix,link-rate = <0x06>;
> > +       analogix,lane-count = <2>;
> > +       analogix,hpd-gpio = <&gpx2 6 0>;
> >
> >          ports {
> >                  port@0 {
> > diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts
> > index 98871f9..fd46714 100644
> > --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts
> > +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts
> > @@ -91,12 +91,10 @@
> >   &dp {
> >          pinctrl-names = "default";
> >          pinctrl-0 = <&dp_hpd>;
> > -       samsung,color-space = <0>;
> > -       samsung,dynamic-range = <0>;
> > -       samsung,ycbcr-coeff = <0>;
> > -       samsung,color-depth = <1>;
> > -       samsung,link-rate = <0x0a>;
> > -       samsung,lane-count = <4>;
> > +       analogix,color-space = <0>;
> > +       analogix,color-depth = <1>;
> > +       analogix,link-rate = <0x0a>;
> > +       analogix,lane-count = <4>;
> >          status = "okay";
> >   };
> >
> > diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
> > index 7d5b386..54b4c63 100644
> > --- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
> > +++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
> > @@ -141,13 +141,11 @@
> >          status = "okay";
> >          pinctrl-names = "default";
> >          pinctrl-0 = <&dp_hpd_gpio>;
> > -       samsung,color-space = <0>;
> > -       samsung,dynamic-range = <0>;
> > -       samsung,ycbcr-coeff = <0>;
> > -       samsung,color-depth = <1>;
> > -       samsung,link-rate = <0x0a>;
> > -       samsung,lane-count = <2>;
> > -       samsung,hpd-gpio = <&gpx2 6 0>;
> > +       analogix,color-space = <0>;
> > +       analogix,color-depth = <1>;
> > +       analogix,link-rate = <0x0a>;
> > +       analogix,lane-count = <2>;
> > +       analogix,hpd-gpio = <&gpx2 6 0>;
> >          panel = <&panel>;
> >   };
> >
> > --
> > 1.9.1
> >
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel


--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html