On Fri, Aug 07, 2015 at 05:53:01PM +0800, Chen Haibo-B51421 wrote: > > > > -----Original Message----- > > From: Dong Aisheng [mailto:aisheng.dong@xxxxxxxxxxxxx] > > Sent: Friday, August 07, 2015 3:39 PM > > To: Chen Haibo-B51421 > > Cc: robh+dt@xxxxxxxxxx; pawel.moll@xxxxxxx; mark.rutland@xxxxxxx; > > ijc+devicetree@xxxxxxxxxxxxxx; galak@xxxxxxxxxxxxxx; shawnguo@xxxxxxxxxx; > > kernel@xxxxxxxxxxxxxx; linux@xxxxxxxxxxxxxxxx; ulf.hansson@xxxxxxxxxx; > > johan.derycke@xxxxxxxxx; mkl@xxxxxxxxxxxxxx; Estevam Fabio-R49496; Dong > > Aisheng-B29396; devicetree@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; > > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; linux-mmc@xxxxxxxxxxxxxxx > > Subject: Re: [PATCH v4 1/6] mmc: sdhci-esdhc-imx: add imx7d support and > > support HS400 > > > > On Wed, Aug 05, 2015 at 06:38:37PM +0800, Haibo Chen wrote: > > > The imx7d usdhc is derived from imx6sx, the difference is that imx7d > > > support HS400. > > > > > > So introduce a new compatible string for imx7d and add HS400 support > > > for imx7d usdhc. > > > > > > Signed-off-by: Haibo Chen <haibo.chen@xxxxxxxxxxxxx> > > > --- > > > drivers/mmc/host/sdhci-esdhc-imx.c | 81 > > > ++++++++++++++++++++++++++++++++++++++ > > > 1 file changed, 81 insertions(+) > > > > > > diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c > > > b/drivers/mmc/host/sdhci-esdhc-imx.c > > > index c6b9f64..48f009c 100644 > > > --- a/drivers/mmc/host/sdhci-esdhc-imx.c > > > +++ b/drivers/mmc/host/sdhci-esdhc-imx.c > > > @@ -44,6 +44,7 @@ > > > #define ESDHC_MIX_CTRL_EXE_TUNE (1 << 22) > > > #define ESDHC_MIX_CTRL_SMPCLK_SEL (1 << 23) > > > #define ESDHC_MIX_CTRL_FBCLK_SEL (1 << 25) > > > +#define ESDHC_MIX_CTRL_HS400_EN (1 << 26) > > > /* Bits 3 and 6 are not SDHCI standard definitions */ > > > #define ESDHC_MIX_CTRL_SDHCI_MASK 0xb7 > > > /* Tuning bits */ > > > @@ -60,6 +61,16 @@ > > > #define ESDHC_TUNE_CTRL_MIN 0 > > > #define ESDHC_TUNE_CTRL_MAX ((1 << 7) - 1) > > > > > > +/* strobe dll register */ > > > +#define ESDHC_STROBE_DLL_CTRL 0x70 > > > +#define ESDHC_STROBE_DLL_CTRL_ENABLE (1 << 0) > > > +#define ESDHC_STROBE_DLL_CTRL_RESET (1 << 1) > > > +#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT 3 > > > + > > > +#define ESDHC_STROBE_DLL_STATUS 0x74 > > > +#define ESDHC_STROBE_DLL_STS_REF_LOCK (1 << 1) > > > +#define ESDHC_STROBE_DLL_STS_SLV_LOCK 0x1 > > > + > > > #define ESDHC_TUNING_CTRL 0xcc > > > #define ESDHC_STD_TUNING_EN (1 << 24) > > > /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */ @@ > > > -120,6 +131,11 @@ > > > #define ESDHC_FLAG_ERR004536 BIT(7) > > > /* The IP supports HS200 mode */ > > > #define ESDHC_FLAG_HS200 BIT(8) > > > +/* The IP supports HS400 mode */ > > > +#define ESDHC_FLAG_HS400 BIT(9) > > > + > > > +/* A higher clock ferquency than this rate requires strobell dll > > control */ > > > +#define ESDHC_STROBE_DLL_CLK_FREQ 100000000 > > > > > > struct esdhc_soc_data { > > > u32 flags; > > > @@ -156,6 +172,12 @@ static struct esdhc_soc_data usdhc_imx6sx_data = { > > > | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200, }; > > > > > > +static struct esdhc_soc_data usdhc_imx7d_data = { > > > + .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING > > > + | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 > > > + | ESDHC_FLAG_HS400, > > > +}; > > > + > > > struct pltfm_imx_data { > > > u32 scratchpad; > > > struct pinctrl *pinctrl; > > > @@ -199,6 +221,7 @@ static const struct of_device_id imx_esdhc_dt_ids[] > > = { > > > { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, }, > > > { .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, }, > > > { .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, }, > > > + { .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, }, > > > { /* sentinel */ } > > > }; > > > MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids); @@ -274,6 +297,9 @@ static > > > u32 esdhc_readl_le(struct sdhci_host *host, int reg) > > > val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104 > > > | SDHCI_SUPPORT_SDR50 > > > | SDHCI_USE_SDR50_TUNING; > > > + > > > + if (imx_data->socdata->flags & ESDHC_FLAG_HS400) > > > + val |= SDHCI_SUPPORT_HS400; > > > } > > > } > > > > > > @@ -774,6 +800,7 @@ static int esdhc_change_pinstate(struct sdhci_host > > *host, > > > break; > > > case MMC_TIMING_UHS_SDR104: > > > case MMC_TIMING_MMC_HS200: > > > + case MMC_TIMING_MMC_HS400: > > > pinctrl = imx_data->pins_200mhz; > > > break; > > > default: > > > @@ -784,6 +811,44 @@ static int esdhc_change_pinstate(struct sdhci_host > > *host, > > > return pinctrl_select_state(imx_data->pinctrl, pinctrl); } > > > > > > +/* > > > + * For HS400 eMMC, there is a data_strobe line, this signal is > > > +generated > > > + * by the device and used for data output and CRC status response > > > +output > > > + * in HS400 mode. The frequency of this signal follows the frequency > > > +of > > > + * CLK generated by host. Host receive the data which is aligned to > > > +the > > > + * edge of data_strobe line. Due to the time delay between CLK line > > > +and > > > + * data_strobe line, if the delay time is larger than one clock > > > +cycle, > > > + * then CLK and data_strobe line will misaligned, read error shows up. > > > + * So when the CLK is higher than 100MHz, each clock cycle is short > > > +enough, > > > + * host should config the delay target. > > > + */ > > > +static void esdhc_set_strobe_dll(struct sdhci_host *host) { > > > + u32 v; > > > + > > > + if (host->mmc->actual_clock > ESDHC_STROBE_DLL_CLK_FREQ) { > > > + /* force a reset on strobe dll */ > > > + writel(ESDHC_STROBE_DLL_CTRL_RESET, > > > + host->ioaddr + ESDHC_STROBE_DLL_CTRL); > > > + /* > > > + * enable strobe dll ctrl and adjust the delay target > > > + * for the uSDHC loopback read clock > > > + */ > > > + v = ESDHC_STROBE_DLL_CTRL_ENABLE | > > > + (7 << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT); > > > + writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL); > > > + /* wait 1us to make sure strobe dll status register stable */ > > > + udelay(1); > > > + v = readl(host->ioaddr + ESDHC_STROBE_DLL_STATUS); > > > + if (!(v & ESDHC_STROBE_DLL_STS_REF_LOCK)) > > > + dev_warn(mmc_dev(host->mmc), > > > + "warning! HS400 strobe DLL status REF not > > lock!\n"); > > > + if (!(v & ESDHC_STROBE_DLL_STS_SLV_LOCK)) > > > + dev_warn(mmc_dev(host->mmc), > > > + "warning! HS400 strobe DLL status SLV not > > lock!\n"); > > > + } > > > +} > > > + > > > static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned > > > timing) { > > > struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); @@ -795,7 > > > +860,13 @@ static void esdhc_set_uhs_signaling(struct sdhci_host *host, > > unsigned timing) > > > case MMC_TIMING_UHS_SDR25: > > > case MMC_TIMING_UHS_SDR50: > > > case MMC_TIMING_UHS_SDR104: > > > + break; > > > case MMC_TIMING_MMC_HS200: > > > + /* disable ddr mode and disable HS400 mode */ > > > + writel(readl(host->ioaddr + ESDHC_MIX_CTRL) & > > > + ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN), > > > + host->ioaddr + ESDHC_MIX_CTRL); > > > + imx_data->is_ddr = 0; > > > > Can you please explain why need above code? > > Any issues if not do it? > > > > Regards > > Dong Aisheng > > [haibo] currently, mmc core code use mmc_retune before every request, > and in mmc_retune, for eMMC, if the chip is in HS400 mode, firstly, > the code use mmc_hs400_to_hs200() to change the emmc chip work in > HS200 mode, and execute the tuning, and then use mmc_hs200_to_hs400() > to make the emmc chip work back in HS400 mode. > > Without the above code, when change to hs200 mode from hs400 mode, our > host still enable ddr mode and enable hs400 mode, which is wrong. > So add the code here. > Okay, understand. Clearing only for HS200 case is a bit confusing. A common rule to do it might be: Step 1) Clear exist timing setting at first Step 2) Set the required timing for each case I'd suggest you do like as follows: m = readl(host->ioaddr + ESDHC_MIX_CTRL); m &=~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN); imx_data->is_ddr = 0; Then case HS200: ... case HS400: ... Regards Dong Aisheng > > > > > break; > > > case MMC_TIMING_UHS_DDR50: > > > case MMC_TIMING_MMC_DDR52: > > > @@ -813,6 +884,13 @@ static void esdhc_set_uhs_signaling(struct > > sdhci_host *host, unsigned timing) > > > writel(v, host->ioaddr + ESDHC_DLL_CTRL); > > > } > > > break; > > > + case MMC_TIMING_MMC_HS400: > > > + writel(readl(host->ioaddr + ESDHC_MIX_CTRL) | > > > + ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN, > > > + host->ioaddr + ESDHC_MIX_CTRL); > > > + imx_data->is_ddr = 1; > > > + esdhc_set_strobe_dll(host); > > > + break; > > > } > > > > > > esdhc_change_pinstate(host, timing); @@ -1100,6 +1178,9 @@ static > > > int sdhci_esdhc_imx_probe(struct platform_device *pdev) > > > if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536) > > > host->quirks |= SDHCI_QUIRK_BROKEN_ADMA; > > > > > > + if (imx_data->socdata->flags & ESDHC_FLAG_HS400) > > > + host->quirks2 |= SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400; > > > + > > > if (of_id) > > > err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data); > > > else > > > -- > > > 1.9.1 > > > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
