On 13/07/15 19:54, Stefan Wahren wrote:
Hi Srinivas,
[add Ezequiel Garcia to CC]
Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx> hat am 10. Juli 2015 um
11:43 geschrieben:
Hi Greg,
This patchset adds a new simple NVMEM framework to kernel, and it is tested
with various drivers like "QCOM thermal sensors", "QCOM cpr driver",
"begal bone cape manager" and few more on the way.
Thankyou all for providing inputs and comments on previous versions of this
patchset. Here is the v7 of the patchset addressing all the issues raised as
part of previous versions review.
Up until now, NVMEM drivers like eeprom were stored in drivers/misc, where
they
all had to duplicate pretty much the same code to register a sysfs file, allow
in-kernel users to access the content of the devices they were driving, etc.
This was also a problem as far as other in-kernel users were involved, since
the solutions used were pretty much different from on driver to another, there
was a rather big abstraction leak.
i only want to mention that there are more places of NVMEM drivers like:
drivers/mfd/ab3100-otp.c
drivers/soc/tegra/fuse/*.c
Thanks for mentioning.
Introduction of this framework aims at solving this. It also introduces DT
representation for consumer devices to go get the data they require (MAC
Addresses, SoC/Revision ID, part numbers, and so on) from the NVMEMs.
After learning few things about QCOM qfprom and other eeprom/efuses, which
has packed fields at bit level. Which makes it important to add support to
such memories. This version adds support to this type of non volatile
memories by adding support to bit level nvmem-cells.
Having regmap interface to this framework would give much better
abstraction for nvmems on different buses.
patch 1-4 Introduces the NVMEM framework.
Patch 5-6 Adds Qualcomm specific qfprom driver.
Patch 7 migrates an existing driver to nvmem framework.
Patch 8 adds entry in MAINTAINERS.
Its also possible to migrate other nvmem drivers to this framework, and I
think
some of them already posted patches based on this framework.
Providers APIs:
nvmem_register/unregister();
How do i get the cell info from the devicetree into the nvmem_config?
Not sure what is the real use-case here, But this is how it is supposed
to work.
cellinfo in nvmem_config is used to pass cell information in non-dt
style to the core. The core would parse it and convert into nvmem-cells.
Am not sure why would you want to do other way round. Could you explain
the real use case here?
I expected a function something like of_nvmem_cell_info_get() in the Providers
API.
...
userspace interface: binary file in /sys/bus/nvmem/devices/*/nvmem
ex:
hexdump /sys/bus/nvmem/devices/qfprom0/nvmem
0000000 0000 0000 0000 0000 0000 0000 0000 0000
*
00000a0 db10 2240 0000 e000 0c00 0c00 0000 0c00
0000000 0000 0000 0000 0000 0000 0000 0000 0000
...
*
0001000
Since we're entering userspace the behavior should be clear.
How do we treat register gaps? Fill them with zero?
nvmem file would read full nvmem size which is passed to it as regmap.
So It would dump whatever the provider returns.
--srini
Best regards
Stefan
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
