Hi Srinivas,
[add Ezequiel Garcia to CC]
> Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx> hat am 10. Juli 2015 um
> 11:43 geschrieben:
>
>
> Hi Greg,
>
> This patchset adds a new simple NVMEM framework to kernel, and it is tested
> with various drivers like "QCOM thermal sensors", "QCOM cpr driver",
> "begal bone cape manager" and few more on the way.
>
> Thankyou all for providing inputs and comments on previous versions of this
> patchset. Here is the v7 of the patchset addressing all the issues raised as
> part of previous versions review.
>
> Up until now, NVMEM drivers like eeprom were stored in drivers/misc, where
> they
> all had to duplicate pretty much the same code to register a sysfs file, allow
> in-kernel users to access the content of the devices they were driving, etc.
> This was also a problem as far as other in-kernel users were involved, since
> the solutions used were pretty much different from on driver to another, there
> was a rather big abstraction leak.
i only want to mention that there are more places of NVMEM drivers like:
drivers/mfd/ab3100-otp.c
drivers/soc/tegra/fuse/*.c
>
> Introduction of this framework aims at solving this. It also introduces DT
> representation for consumer devices to go get the data they require (MAC
> Addresses, SoC/Revision ID, part numbers, and so on) from the NVMEMs.
>
> After learning few things about QCOM qfprom and other eeprom/efuses, which
> has packed fields at bit level. Which makes it important to add support to
> such memories. This version adds support to this type of non volatile
> memories by adding support to bit level nvmem-cells.
>
> Having regmap interface to this framework would give much better
> abstraction for nvmems on different buses.
>
> patch 1-4 Introduces the NVMEM framework.
> Patch 5-6 Adds Qualcomm specific qfprom driver.
> Patch 7 migrates an existing driver to nvmem framework.
> Patch 8 adds entry in MAINTAINERS.
>
> Its also possible to migrate other nvmem drivers to this framework, and I
> think
> some of them already posted patches based on this framework.
>
> Providers APIs:
> nvmem_register/unregister();
How do i get the cell info from the devicetree into the nvmem_config?
I expected a function something like of_nvmem_cell_info_get() in the Providers
API.
>
> Consumers APIs:
> Cell based apis for both DT/Non-DT:
> nvmem_cell_get()/nvmem_cell_put();
> devm_nvmem_cell_get()/devm_nvmem_cell_put();
> of_nvmem_cell_get()
> nvmem_cell_read()/nvmem_cell_write();
>
> Raw byte access apis for both DT/non-DT.
> nvmem_device_get()/nvmem_device_put()
> devm_nvmem_device_get()/nvmem_device_put()
> of_nvmem_device_get()
>
> nvmem_device_read()/nvmem_device_write();
> nvmem_device_cell_read()/nvmem_device_cell_write();
>
> Device Tree:
>
> /* Provider */
> qfprom: qfprom@00700000 {
> ...
>
> /* Data cells */
> tsens_calibration: calib@404 {
> reg = <0x404 0x10>;
> };
>
> tsens_calibration_bckp: calib_bckp@504 {
> reg = <0x504 0x11>;
> bit-offset = 6;
> nbits = 128;
> };
>
> pvs_version: pvs-version@6 {
> reg = <0x6 0x2>
> bit-offset = 7;
> nbits = 2;
> };
>
> speed_bin: speed-bin@c{
> reg = <0xc 0x1>;
> bit-offset = 2;
> nbits = 3;
>
> };
> ...
> };
> /* Consumer */
> tsens {
> ...
> nvmem-cells = <&tsens_calibration>;
> nvmem-cell-names = "calibration";
> };
>
> userspace interface: binary file in /sys/bus/nvmem/devices/*/nvmem
>
> ex:
> hexdump /sys/bus/nvmem/devices/qfprom0/nvmem
>
> 0000000 0000 0000 0000 0000 0000 0000 0000 0000
> *
> 00000a0 db10 2240 0000 e000 0c00 0c00 0000 0c00
> 0000000 0000 0000 0000 0000 0000 0000 0000 0000
> ...
> *
> 0001000
Since we're entering userspace the behavior should be clear.
How do we treat register gaps? Fill them with zero?
Best regards
Stefan
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
