This patch adds init time configuration of 88PM800/805 and
88PM860. It includes,
- Enable BUCK clock gating in low power mode
- Full mode support for BUCK2 and 4
- Enable voltage change (LPF, DVC) in PMIC
Note that both 88PM800 and 88PM860 do share common configurations,
but since I can not validate the configuration on 88PM800,
restricting myself only to 88PM860.
If anyone can validate on 88PM800, we can move common code accordingly.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@xxxxxxxxxx>
---
drivers/mfd/88pm800.c | 64 +++++++++++++++++++++++++++++++++++++++++++++
include/linux/mfd/88pm80x.h | 13 +++++++++
2 files changed, 77 insertions(+)
diff --git a/drivers/mfd/88pm800.c b/drivers/mfd/88pm800.c
index 95c8ad4..80a1bc1 100644
--- a/drivers/mfd/88pm800.c
+++ b/drivers/mfd/88pm800.c
@@ -521,6 +521,63 @@ out:
return ret;
}
+static int pm800_init_config(struct pm80x_chip *chip, struct device_node *np)
+{
+ int ret;
+ unsigned int val;
+
+ switch (chip->type) {
+ case CHIP_PM800:
+ case CHIP_PM805:
+ break;
+ case CHIP_PM860:
+ /* Enable LDO and BUCK clock gating in low power mode */
+ ret = regmap_update_bits(chip->regmap, PM800_LOW_POWER_CONFIG3,
+ PM800_LDOBK_FREEZE, PM800_LDOBK_FREEZE);
+ if (ret)
+ goto error;
+
+ /* Enable voltage change in pmic, POWER_HOLD = 1 */
+ ret = regmap_update_bits(chip->regmap, PM800_WAKEUP1,
+ PM800_PWR_HOLD_EN, PM800_PWR_HOLD_EN);
+ if (ret)
+ goto error;
+
+ /*
+ * Set buck2 and buck4 driver selection to be full.
+ * The default value is 0, for full drive support
+ * it should be set to 1.
+ * In A1 version it will be set to 1 by default.
+ * To be on safer side, set it explicitly
+ */
+ ret = regmap_update_bits(chip->subchip->regmap_power,
+ PM860_BUCK2_MISC2,
+ PM860_BUCK2_FULL_DRV,
+ PM860_BUCK2_FULL_DRV);
+ if (ret)
+ goto error;
+
+ ret = regmap_update_bits(chip->subchip->regmap_power,
+ PM860_BUCK4_MISC2,
+ PM860_BUCK4_FULL_DRV,
+ PM860_BUCK4_FULL_DRV);
+ if (ret)
+ goto error;
+
+
+ break;
+ default:
+ dev_err(chip->dev, "Unknown device type: %d\n", chip->type);
+ break;
+ }
+
+ return 0;
+
+error:
+ dev_err(chip->dev, "failed to access registers\n");
+ return ret;
+}
+
static int pm800_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
@@ -585,6 +642,13 @@ static int pm800_probe(struct i2c_client *client,
if (pdata->plat_config)
pdata->plat_config(chip, pdata);
+ /* common register configurations , init time only */
+ ret = pm800_init_config(chip, np);
+ if (ret) {
+ dev_err(chip->dev, "Failed to configure 88pm800 devices\n");
+ goto err_device_init;
+ }
+
return 0;
err_device_init:
diff --git a/include/linux/mfd/88pm80x.h b/include/linux/mfd/88pm80x.h
index 2e25fb1..2ef62af 100644
--- a/include/linux/mfd/88pm80x.h
+++ b/include/linux/mfd/88pm80x.h
@@ -74,6 +74,7 @@ enum {
/* Wakeup Registers */
#define PM800_WAKEUP1 (0x0D)
+#define PM800_PWR_HOLD_EN BIT(7)
#define PM800_WAKEUP2 (0x0E)
#define PM800_WAKEUP2_INV_INT BIT(0)
@@ -87,7 +88,10 @@ enum {
/* Referance and low power registers */
#define PM800_LOW_POWER1 (0x20)
#define PM800_LOW_POWER2 (0x21)
+
#define PM800_LOW_POWER_CONFIG3 (0x22)
+#define PM800_LDOBK_FREEZE BIT(7)
+
#define PM800_LOW_POWER_CONFIG4 (0x23)
/* GPIO register */
@@ -279,6 +283,15 @@ enum {
#define PM805_EARPHONE_SETTING (0x29)
#define PM805_AUTO_SEQ_SETTING (0x2A)
+
+/* 88PM860 Registers */
+
+#define PM860_BUCK2_MISC2 (0x7C)
+#define PM860_BUCK2_FULL_DRV BIT(2)
+
+#define PM860_BUCK4_MISC2 (0x82)
+#define PM860_BUCK4_FULL_DRV BIT(2)
+
struct pm80x_rtc_pdata {
int vrtc;
int rtc_wakeup;
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
