Re: [PATCH 3/5] soc: Mediatek: Add SCPSYS power domain driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Tue, May 12, 2015 at 3:23 AM, Sascha Hauer <s.hauer@xxxxxxxxxxxxxx> wrote:
> This adds a power domain driver for the Mediatek SCPSYS unit.
>
> The System Control Processor System (SCPSYS) has several power
> management related tasks in the system. The tasks include thermal
> measurement, dynamic voltage frequency scaling (DVFS), interrupt
> filter and lowlevel sleep control. The System Power Manager (SPM)
> inside the SCPSYS is for the MTCMOS power domain control.
>
> For now this driver only adds power domain support, the more
> advanced features are not yet supported. The driver implements
> the generic PM domain device tree bindings, the first user will
> most likely be the Mediatek AFE audio driver.
>
> Signed-off-by: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
> ---
>  .../devicetree/bindings/soc/mediatek/scpsys.txt    |   2 +
>  drivers/soc/mediatek/Kconfig                       |   8 +
>  drivers/soc/mediatek/Makefile                      |   1 +
>  drivers/soc/mediatek/mtk-scpsys.c                  | 416 +++++++++++++++++++++
>  include/dt-bindings/power/mt8173-power.h           |  15 +
>  5 files changed, 442 insertions(+)
>  create mode 100644 drivers/soc/mediatek/mtk-scpsys.c
>  create mode 100644 include/dt-bindings/power/mt8173-power.h
>
> diff --git a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt
> index 4764a03..87f2091 100644
> --- a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt
> +++ b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt
> @@ -15,6 +15,7 @@ Required properties:
>  - compatible: Must be "mediatek,mt8173-scpsys"
>  - #power-domain-cells: Must be 1
>  - reg: Address range of the SCPSYS unit
> +- infracfg: must contain a phandle to the infracfg controller
>
>  Example:
>
> @@ -22,6 +23,7 @@ Example:
>                 #power-domain-cells = <1>;
>                 compatible = "mediatek,mt8173-scpsys";
>                 reg = <0 0x10006000 0 0x1000>;
> +               infracfg = <&infracfg>;
>         };
>
>  Example consumer:
> diff --git a/drivers/soc/mediatek/Kconfig b/drivers/soc/mediatek/Kconfig
> index 6fae66f..1386c79 100644
> --- a/drivers/soc/mediatek/Kconfig
> +++ b/drivers/soc/mediatek/Kconfig
> @@ -18,3 +18,11 @@ config MTK_INFRACFG
>           Say yes here to add support for the MediaTek INFRACFG controller. The
>           INFRACFG controller contains various infrastructure registers not
>           directly associated to any device.
> +
> +config MTK_SCPSYS
> +       tristate "MediaTek SCPSYS Support"
> +       depends on MTK_INFRACFG

Should this be:
  depends on ARCH_MEDIATEK || COMPILE_TEST
  selects MTK_INFRACFG

> +       select REGMAP
> +       help
> +         Say yes here to add support for the MediaTek SCPSYS power domain
> +         driver.
> diff --git a/drivers/soc/mediatek/Makefile b/drivers/soc/mediatek/Makefile
> index ce39119..f8eebab 100644
> --- a/drivers/soc/mediatek/Makefile
> +++ b/drivers/soc/mediatek/Makefile
> @@ -1,2 +1,3 @@
>  obj-$(CONFIG_MTK_PMIC_WRAP) += mtk-pmic-wrap.o
>  obj-$(CONFIG_MTK_INFRACFG) += mtk-infracfg.o
> +obj-$(CONFIG_MTK_SCPSYS) += mtk-scpsys.o
> diff --git a/drivers/soc/mediatek/mtk-scpsys.c b/drivers/soc/mediatek/mtk-scpsys.c
> new file mode 100644
> index 0000000..c42c7f1
> --- /dev/null
> +++ b/drivers/soc/mediatek/mtk-scpsys.c
> @@ -0,0 +1,416 @@
> +/*
> + * Copyright (c) 2015 Pengutronix, Sascha Hauer <kernel@xxxxxxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +#include <linux/clk.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/pm_domain.h>
> +#include <linux/delay.h>
> +#include <linux/soc/mediatek/infracfg.h>
> +#include <dt-bindings/power/mt8173-power.h>
> +#include <linux/mfd/syscon.h>
> +
> +#define SPM_VDE_PWR_CON                        0x0210
> +#define SPM_MFG_PWR_CON                        0x0214
> +#define SPM_VEN_PWR_CON                        0x0230
> +#define SPM_ISP_PWR_CON                        0x0238
> +#define SPM_DIS_PWR_CON                        0x023c
> +#define SPM_VEN2_PWR_CON               0x0298
> +#define SPM_AUDIO_PWR_CON              0x029c
> +#define SPM_MFG_2D_PWR_CON             0x02c0
> +#define SPM_MFG_ASYNC_PWR_CON          0x02c4
> +#define SPM_USB_PWR_CON                        0x02cc
> +#define SPM_PWR_STATUS                 0x060c
> +#define SPM_PWR_STATUS_2ND             0x0610
> +
> +#define PWR_RST_B_BIT                  BIT(0)
> +#define PWR_ISO_BIT                    BIT(1)
> +#define PWR_ON_BIT                     BIT(2)
> +#define PWR_ON_2ND_BIT                 BIT(3)
> +#define PWR_CLK_DIS_BIT                        BIT(4)
> +
> +#define DIS_PWR_STA_MASK               BIT(3)
> +#define MFG_PWR_STA_MASK               BIT(4)
> +#define ISP_PWR_STA_MASK               BIT(5)
> +#define VDE_PWR_STA_MASK               BIT(7)
> +#define VEN2_PWR_STA_MASK              BIT(20)
> +#define VEN_PWR_STA_MASK               BIT(21)
> +#define MFG_2D_PWR_STA_MASK            BIT(22)
> +#define MFG_ASYNC_PWR_STA_MASK         BIT(23)
> +#define AUDIO_PWR_STA_MASK             BIT(24)
> +#define USB_PWR_STA_MASK               BIT(25)
> +
> +struct scp_domain_data {
> +       const char *name;
> +       u32 sta_mask;
> +       int ctl_offs;
> +       u32 sram_pdn_bits;
> +       u32 sram_pdn_ack_bits;
> +       u32 bus_prot_mask;
> +       int id;
> +       const char *clk_name;
> +};

These fields are only used at init time:
 name (the pointer, the actual string is pointed to by genpd->name)
 id
 clk_name

You could split those off into a separate __initconst struct.

> +
> +static const struct scp_domain_data scp_domain_data[] = {
> +       {
> +               .id = MT8173_POWER_DOMAIN_VDE,
> +               .name = "vde",
> +               .sta_mask = VDE_PWR_STA_MASK,
> +               .ctl_offs = SPM_VDE_PWR_CON,
> +               .sram_pdn_bits = GENMASK(11, 8),
> +               .sram_pdn_ack_bits = GENMASK(12, 12),
> +               .clk_name = "vdec",
> +       }, {
> +               .id = MT8173_POWER_DOMAIN_VEN,

Is there any reason you do not keep these in ".id" order:
VDE,  MFG, VEN, ISP, DIS, VEN2, AUDIO, MFG_2D, MFG_ASYNC, USB

If you want to make the ID defines explicit in the code, you can
instead get rid of the '.id' field, and use the defines as indices
while initializing the scp_domain_data array:

 static const struct scp_domain_data scp_domain_data[] = {
    [MT8173_POWER_DOMAIN_VDE] = { },
    [MT8173_POWER_DOMAIN_MFG] = { },
    ...
 };

> +               .name = "ven",
> +               .sta_mask = VEN_PWR_STA_MASK,
> +               .ctl_offs = SPM_VEN_PWR_CON,
> +               .sram_pdn_bits = GENMASK(11, 8),
> +               .sram_pdn_ack_bits = GENMASK(15, 12),
> +               .clk_name = "venc",
> +       }, {
> +               .id = MT8173_POWER_DOMAIN_ISP,
> +               .name = "isp",
> +               .sta_mask = ISP_PWR_STA_MASK,
> +               .ctl_offs = SPM_ISP_PWR_CON,
> +               .sram_pdn_bits = GENMASK(11, 8),
> +               .sram_pdn_ack_bits = GENMASK(13, 12),
> +       }, {
> +               .id = MT8173_POWER_DOMAIN_DIS,
> +               .name = "disp",

Perhaps .id/.name/.clk should be "MM" to match the corresponding clock
define (CLK_TOP_MM_SEL) & prot bits.

> +               .sta_mask = DIS_PWR_STA_MASK,
> +               .ctl_offs = SPM_DIS_PWR_CON,
> +               .sram_pdn_bits = GENMASK(11, 8),
> +               .sram_pdn_ack_bits = GENMASK(12, 12),
> +               .clk_name = "disp",
> +               .bus_prot_mask = MT8173_TOP_AXI_PROT_EN_MM_M0 |
> +                       MT8173_TOP_AXI_PROT_EN_MM_M1,
> +       }, {
> +               .id = MT8173_POWER_DOMAIN_VEN2,
> +               .name = "ven2",

Perhaps .id/.name/.clk should be "VENC_LT"/"venc_lt" to match the
corresponding clock define (CLK_TOP_VENC_LT_SEL).

> +               .sta_mask = VEN2_PWR_STA_MASK,
> +               .ctl_offs = SPM_VEN2_PWR_CON,
> +               .sram_pdn_bits = GENMASK(11, 8),
> +               .sram_pdn_ack_bits = GENMASK(15, 12),
> +               .clk_name = "ven2",
> +       }, {
> +               .id = MT8173_POWER_DOMAIN_AUDIO,
> +               .name = "audio",
> +               .sta_mask = AUDIO_PWR_STA_MASK,
> +               .ctl_offs = SPM_AUDIO_PWR_CON,
> +               .sram_pdn_bits = GENMASK(11, 8),
> +               .sram_pdn_ack_bits = GENMASK(15, 12),
> +       },  {
> +               .id = MT8173_POWER_DOMAIN_MFG_ASYNC,
> +               .name = "mfg_async",
> +               .sta_mask = MFG_ASYNC_PWR_STA_MASK,
> +               .ctl_offs = SPM_MFG_ASYNC_PWR_CON,
> +               .sram_pdn_bits = GENMASK(11, 8),
> +               .sram_pdn_ack_bits = 0,
> +               .clk_name = "mfg",
> +       }, {
> +               .id = MT8173_POWER_DOMAIN_MFG_2D,
> +               .name = "mfg_2d",
> +               .sta_mask = MFG_2D_PWR_STA_MASK,
> +               .ctl_offs = SPM_MFG_2D_PWR_CON,
> +               .sram_pdn_bits = GENMASK(11, 8),
> +               .sram_pdn_ack_bits = GENMASK(13, 12),
> +               .clk_name = "mfg",
> +       }, {
> +               .id = MT8173_POWER_DOMAIN_MFG,
> +               .name = "mfg",
> +               .sta_mask = MFG_PWR_STA_MASK,
> +               .ctl_offs = SPM_MFG_PWR_CON,
> +               .sram_pdn_bits = GENMASK(13, 8),
> +               .sram_pdn_ack_bits = GENMASK(21, 16),
> +               .clk_name = "mfg",
> +               .bus_prot_mask = MT8173_TOP_AXI_PROT_EN_MFG_S |
> +                       MT8173_TOP_AXI_PROT_EN_MFG_M0 |
> +                       MT8173_TOP_AXI_PROT_EN_MFG_M1 |
> +                       MT8173_TOP_AXI_PROT_EN_MFG_SNOOP_OUT,
> +       }, {
> +               .id = MT8173_POWER_DOMAIN_USB,
> +               .name = "usb",
> +               .sta_mask = USB_PWR_STA_MASK,
> +               .ctl_offs = SPM_USB_PWR_CON,
> +               .sram_pdn_bits = GENMASK(11, 8),
> +               .sram_pdn_ack_bits = GENMASK(15, 12),
> +       },
> +};
> +
> +#define NUM_DOMAINS    ARRAY_SIZE(scp_domain_data)
> +
> +struct scp;
> +
> +struct scp_domain {
> +       struct generic_pm_domain pmd;

Could you name this "genpd"... that seems to be what most other drivers use.

> +       const struct scp_domain_data *data;
> +       struct scp *scp;
> +       struct clk *clk;
> +};
> +
> +struct scp {
> +       struct scp_domain domains[NUM_DOMAINS];
> +       struct genpd_onecell_data pd_data;

After probe() you don't use pd_data.
Why do we need it in this struct?

> +       struct device *dev;
> +       void __iomem *base;
> +       struct regmap *infracfg;
> +};
> +
> +static int scpsys_power_on(struct generic_pm_domain *genpd)
> +{
> +       struct scp_domain *scpd = container_of(genpd, struct scp_domain, pmd);
> +       struct scp *scp = scpd->scp;
> +       const struct scp_domain_data *data = scpd->data;
> +       unsigned long expired;
> +       void __iomem *ctl_addr = scpd->scp->base + data->ctl_offs;
> +       u32 sram_pdn_ack = data->sram_pdn_ack_bits;
> +       u32 val;
> +       int ret;
> +
> +       if (scpd->clk) {
> +               ret = clk_prepare_enable(scpd->clk);
> +               if (ret)
> +                       return ret;
> +       }
> +
> +       val = readl(ctl_addr);
> +       val |= PWR_ON_BIT;
> +       writel(val, ctl_addr);
> +       val |= PWR_ON_2ND_BIT;
> +       writel(val, ctl_addr);
> +
> +       /* wait until PWR_ACK = 1 */
> +       expired = jiffies + HZ;
> +       while (!(readl(scp->base + SPM_PWR_STATUS) & data->sta_mask) ||
> +                       !(readl(scp->base + SPM_PWR_STATUS_2ND) & data->sta_mask)) {
> +               cpu_relax();
> +               if (time_after(jiffies, expired)) {
> +                       ret = -EIO;
> +                       goto out;
> +               }
> +       }
> +
> +       val &= ~PWR_CLK_DIS_BIT;
> +       writel(val, ctl_addr);
> +
> +       val &= ~PWR_ISO_BIT;
> +       writel(val, ctl_addr);
> +
> +       val |= PWR_RST_B_BIT;
> +       writel(val, ctl_addr);
> +
> +       val &= ~data->sram_pdn_bits;
> +       writel(val, ctl_addr);
> +
> +       /* wait until SRAM_PDN_ACK all 0 */
> +       expired = jiffies + HZ;
> +       while (sram_pdn_ack && (readl(ctl_addr) & sram_pdn_ack)) {
> +               cpu_relax();
> +               if (time_after(jiffies, expired)) {
> +                       ret = -EIO;
> +                       goto out;
> +               }
> +       }
> +
> +       if (data->bus_prot_mask) {
> +               ret = mtk_infracfg_clear_bus_protection(scp->infracfg,
> +                               data->bus_prot_mask);
> +               if (ret)
> +                       return ret;
> +       }
> +
> +       return 0;
> +out:
> +       dev_err(scp->dev, "Failed to power on domain %s\n", scpd->data->name);

genpd->name should be sufficient

> +
> +       return ret;
> +}
> +
> +static int scpsys_power_off(struct generic_pm_domain *genpd)
> +{
> +       struct scp_domain *scpd = container_of(genpd, struct scp_domain, pmd);
> +       struct scp *scp = scpd->scp;
> +       const struct scp_domain_data *data = scpd->data;
> +       unsigned long expired;
> +       void __iomem *ctl_addr = scpd->scp->base + data->ctl_offs;
> +       u32 sram_pdn_ack = data->sram_pdn_ack_bits;
> +       u32 val;
> +       int ret;
> +
> +       if (data->bus_prot_mask) {
> +               ret = mtk_infracfg_set_bus_protection(scp->infracfg,
> +                               data->bus_prot_mask);
> +               if (ret)
> +                       return ret;
> +       }
> +
> +       val = readl(ctl_addr);
> +       val |= data->sram_pdn_bits;
> +       writel(val, ctl_addr);
> +
> +       /* wait until SRAM_PDN_ACK all 1 */
> +       expired = jiffies + HZ;
> +       while ((readl(ctl_addr) & sram_pdn_ack) != sram_pdn_ack) {
> +               cpu_relax();
> +               if (time_after(jiffies, expired)) {
> +                       ret = -EIO;
> +                       goto out;
> +               }
> +       }
> +
> +       val |= PWR_ISO_BIT;
> +       writel(val, ctl_addr);
> +
> +       val &= ~PWR_RST_B_BIT;
> +       writel(val, ctl_addr);
> +
> +       val |= PWR_CLK_DIS_BIT;
> +       writel(val, ctl_addr);
> +
> +       val &= ~PWR_ON_BIT;
> +       writel(val, ctl_addr);
> +
> +       val &= ~PWR_ON_2ND_BIT;
> +       writel(val, ctl_addr);
> +
> +       /* wait until PWR_ACK = 0 */
> +       expired = jiffies + HZ;
> +       while ((readl(scp->base + SPM_PWR_STATUS) & data->sta_mask) ||
> +                       (readl(scp->base + SPM_PWR_STATUS_2ND) & data->sta_mask)) {
> +               cpu_relax();
> +               if (time_after(jiffies, expired)) {
> +                       ret = -EIO;
> +                       goto out;
> +               }
> +       }
> +
> +       if (scpd->clk)
> +               clk_disable_unprepare(scpd->clk);
> +
> +       return 0;
> +
> +out:
> +       dev_err(scp->dev, "Failed to power off domain %s\n", scpd->data->name);
> +
> +       return ret;
> +}
> +
> +static int scpsys_probe(struct platform_device *pdev)
> +{
> +       struct genpd_onecell_data *pd_data;
> +       struct resource *res;
> +       int i;
> +       struct scp *scp;
> +
> +       scp = devm_kzalloc(&pdev->dev, sizeof(*scp), GFP_KERNEL);
> +       if (!scp)
> +               return -ENOMEM;
> +
> +       scp->dev = &pdev->dev;
> +
> +       res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +       scp->base = devm_ioremap_resource(&pdev->dev, res);
> +       if (IS_ERR(scp->base))
> +               return PTR_ERR(scp->base);
> +
> +       pd_data = &scp->pd_data;
> +
> +       pd_data->domains = devm_kzalloc(&pdev->dev,
> +                       sizeof(*pd_data->domains) * NUM_DOMAINS, GFP_KERNEL);
> +       if (!pd_data->domains)
> +               return -ENOMEM;
> +
> +       scp->infracfg = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
> +                       "infracfg");
> +       if (IS_ERR(scp->infracfg)) {
> +               dev_err(&pdev->dev, "Cannot find infracfg controller: %ld\n",
> +                               PTR_ERR(scp->infracfg));
> +               return PTR_ERR(scp->infracfg);
> +       }
> +
> +       pd_data->num_domains = NUM_DOMAINS;
> +
> +       for (i = 0; i < NUM_DOMAINS; i++) {
> +               struct scp_domain *scpd = &scp->domains[i];
> +
> +               if (scp_domain_data[i].clk_name) {
> +                       const char *name = scp_domain_data[i].clk_name;
> +
> +                       scpd->clk = devm_clk_get(&pdev->dev, name);
> +                       if (IS_ERR(scpd->clk)) {
> +                               dev_err(&pdev->dev, "Failed to get %s clk: %ld\n",
> +                                               name, PTR_ERR(scpd->clk));
> +                               return PTR_ERR(scpd->clk);
> +                       }
> +               }
> +       }
> +
> +       for (i = 0; i < NUM_DOMAINS; i++) {
> +               struct scp_domain *scpd = &scp->domains[i];
> +               struct generic_pm_domain *pmd = &scpd->pmd;
> +
> +               pd_data->domains[scp_domain_data[i].id] = pmd;
> +               scpd->data = &scp_domain_data[i];
> +               scpd->scp = scp;
> +
> +               pmd->name = scp_domain_data[i].name;
> +               pmd->power_off = scpsys_power_off;
> +               pmd->power_on = scpsys_power_on;
> +               pmd->power_off_latency_ns = 20000;
> +               pmd->power_on_latency_ns = 20000;

Where did these latency values come from?

> +
> +               pm_genpd_init(pmd, NULL, true);

I'm not sure how this works...  does this mean that all power domains
initially off?

> +
> +               /*
> +                * If PM is disabled turn on all domains by default so that
> +                * consumers can work.
> +                */
> +               if (!IS_ENABLED(CONFIG_PM))
> +                       pmd->power_on(pmd);
> +       }
> +
> +       pm_genpd_add_subdomain(&scp->domains[MT8173_POWER_DOMAIN_MFG_ASYNC].pmd,
> +               &scp->domains[MT8173_POWER_DOMAIN_MFG_2D].pmd);
> +       pm_genpd_add_subdomain(&scp->domains[MT8173_POWER_DOMAIN_MFG_2D].pmd,
> +               &scp->domains[MT8173_POWER_DOMAIN_MFG].pmd);
> +

(1) nit: the continuation lines needs 1 more indent.

(2) Why aren't you checking for errors?

(3) The indexes here are wrong after you re-ordered scp_domain_data[]...

scp->domains[] is ordered by scp_domain_data[] index, not ".id" order
like pd_data->domains[].

So, I think you want:

      pm_genpd_add_subdomain(&pd_data->domains[MT8173_POWER_DOMAIN_MFG_ASYNC],
              &pd_data->domains[MT8173_POWER_DOMAIN_MFG_2D]);

      pm_genpd_add_subdomain(&pd_data->domains[MT8173_POWER_DOMAIN_MFG_2D],
              &pd_data->domains[MT8173_POWER_DOMAIN_MFG]);


Best Regards,
-Dan

> +       return of_genpd_add_provider_onecell(pdev->dev.of_node, pd_data);
> +}
> +
> +static struct of_device_id of_scpsys_match_tbl[] = {
> +       {
> +               .compatible = "mediatek,mt8173-scpsys",
> +       }, {
> +               /* sentinel */
> +       }
> +};
> +MODULE_DEVICE_TABLE(of, of_scpsys_match_tbl);
> +
> +static struct platform_driver scpsys_drv = {
> +       .driver = {
> +               .name = "mtk-scpsys",
> +               .owner = THIS_MODULE,
> +               .of_match_table = of_match_ptr(of_scpsys_match_tbl),
> +       },
> +       .probe = scpsys_probe,
> +};
> +
> +module_platform_driver(scpsys_drv);
> +
> +MODULE_AUTHOR("Sascha Hauer, Pengutronix");
> +MODULE_DESCRIPTION("MediaTek MT8173 scpsys driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/dt-bindings/power/mt8173-power.h b/include/dt-bindings/power/mt8173-power.h
> new file mode 100644
> index 0000000..88715f2
> --- /dev/null
> +++ b/include/dt-bindings/power/mt8173-power.h
> @@ -0,0 +1,15 @@
> +#ifndef _DT_BINDINGS_POWER_MT8183_POWER_H
> +#define _DT_BINDINGS_POWER_MT8183_POWER_H
> +
> +#define MT8173_POWER_DOMAIN_VDE                0
> +#define MT8173_POWER_DOMAIN_MFG                1
> +#define MT8173_POWER_DOMAIN_VEN                2
> +#define MT8173_POWER_DOMAIN_ISP                3
> +#define MT8173_POWER_DOMAIN_DIS                4
> +#define MT8173_POWER_DOMAIN_VEN2       5
> +#define MT8173_POWER_DOMAIN_AUDIO      6
> +#define MT8173_POWER_DOMAIN_MFG_2D     7
> +#define MT8173_POWER_DOMAIN_MFG_ASYNC  8
> +#define MT8173_POWER_DOMAIN_USB                9
> +
> +#endif /* _DT_BINDINGS_POWER_MT8183_POWER_H */
> --
> 2.1.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux