On Wed, May 06, 2015 at 10:06:21AM +0200, Heiko Schocher wrote:
> This patch add support for the imx6dl based aristainetos2 board
> with following configuration:
>
> CPU: Freescale i.MX6DL rev1.1 at 792 MHz
> MReset cause: POR
> MBoard: aristaitenos2
> DRAM: 1 GiB
> NAND: 1024 MiB
> MMC: FSL_SDHC: 0, FSL_SDHC: 1
> SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB
> Display: lb07wv8 (800x480)
>
> As this board can used with 2 different display types, the
> differences between them are extracted into 2 DTS files, and
> the common settings are collected in a common file.
>
> Signed-off-by: Heiko Schocher <hs@xxxxxxx>
> ---
>
> arch/arm/boot/dts/imx6dl-aristainetos2_4.dts | 124 ++++++
> arch/arm/boot/dts/imx6dl-aristainetos2_7.dts | 63 +++
> arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi | 631 +++++++++++++++++++++++++++
> 3 files changed, 818 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-aristainetos2_4.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-aristainetos2_7.dts
> create mode 100644 arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
>
[...]
> +
> +&i2c1 {
> + clock-frequency = <100000>;
I wonder why I see so many I2C nodes with this in this and other board
dts files. Are all these buses so slow? Why not 400000? Also 100000 is
the default anyway.
> +
> + gpio {
> + pinctrl_gpio: gpiogrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0 /* led enable */
> + MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b0 /* backlight enable */
> + MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0 /* LCD power enable */
> + MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x1b0b0 /* led yellow */
> + MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x1b0b0 /* led red */
> + MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x1b0b0 /* led green */
> + MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x1b0b0 /* led blue */
> + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0 /* Profibus IRQ */
> + MX6QDL_PAD_SD3_DAT6__GPIO6_IO18 0x1b0b0 /* FPGA IRQ */
> + MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x1b0b0 /* spi bus #2 SS driver enable */
> + MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b0 /* RST_LOC# PHY reset input (has pull-down!)*/
> + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1b0b0 /* USB_OTG_ID = GPIO1_24*/
> + MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b0b0 /* SD2 level shifter output enable */
> + MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0 /* SD1 card detect input */
> + MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x1b0b0 /* SD1 write protect input */
> + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0 /* SD2 card detect input */
> + MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* SD2 write protect input */
Shouldn't the SD specific pins in the usdhc nodes below? Also backlight
enable, LEDs could also be moved to the corresponding device nodes.
> + MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 /* Touchscreen IRQ */
> + MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x1b0b0 /* PCIe reset */
> + >;
> + };
> + };
> +
> + gpmi-nand {
> + pinctrl_gpmi_nand: gpmi-nand {
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
> + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
> + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
> + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
> + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
> + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
> + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
> + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
> + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
> + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
> + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
> + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
> + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
> + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
> + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
> + >;
> + };
> + };
> +
> + i2c1 {
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
> + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
> + >;
> + };
> + };
> +
> + i2c2 {
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + >;
> + };
> + };
> +
> + i2c3 {
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
> + >;
Please check the indentation here and in some other pinctrl nodes.
Sascha
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
