Hi Yao Zi,
On 2025-03-04 20:49, Yao Zi wrote:
> On Tue, Mar 04, 2025 at 08:10:36PM +0800, Chukun Pan wrote:
>> Hi,
>>
>>> + aliases {
>>> + mmc0 = &sdmmc;
>>
>> s/mmc0/mmc1
>
> Will take it and add the missing pinctrl, as Jonas already pointed out.
>
>>> +&sdmmc {
>>> + bus-width = <4>;
>>> + cap-mmc-highspeed;
>>> + cap-sd-highspeed;
>>
>> I think for sdcard, only cap-sd-highspeed
>> is needed, not cap-mmc-highspeed?
>
> This makes sense, will remove it in the next version.
Please do not remove the cap-mmc-highspeed prop, I tested the controller
with a microSD to eMMC adapter and MMC HS speed is supported:
mmc1: card 59b4 removed
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
mmc_host mmc1: Bus speed (slot 0) = 49800000Hz (slot req 52000000Hz, actual 49800000HZ div = 0)
mmc1: new high speed MMC card at address 0001
mmcblk1: mmc1:0001 DG4008 7.28 GiB
mmcblk1: p1 p2
mmcblk1boot0: mmc1:0001 DG4008 4.00 MiB
mmcblk1boot1: mmc1:0001 DG4008 4.00 MiB
mmcblk1rpmb: mmc1:0001 DG4008 4.00 MiB, chardev (499:0)
~ # cat /sys/kernel/debug/mmc1/ios
clock: 52000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 2 (4 bits)
timing spec: 1 (mmc high-speed)
signal voltage: 0 (3.30 V)
driver type: 0 (driver type B)
Regards,
Jonas
>
>>> + disable-wp;
>>
>> Missing pinctrl.
>>
>>> + rockchip,default-sample-phase = <90>;
>>
>> It seems that all rk3528 devices need to set this
>> default phase, so maybe this can be placed in dtsi?
>
> Yes, since the tuned phase offset is a SoC-specific value, as pointed
> out by comment in the driver,
>
> this is _not_ a value that is dynamically tuned and is also
> _not_ a value that will vary from board to board. It is a value
> that could vary between different SoC models.
>
> Will take it in the next version, thanks for finding it!
>
>>> + sd-uhs-sdr104;
>>
>> The rk3528 devices uses gpio to switch IO voltage, maybe
>> more modes should be added here like vendor kernel?
>
> I cannot get the relationship between things you mentioned. For the
> regulator, yes, here vqmmc-supply is missing, as already pointed out by
> Jonas.
>
>> And these devices use 3.3V IO voltage by default.
>>
>> sd-uhs-sdr12;
>> sd-uhs-sdr25;
>> sd-uhs-sdr50;
>> sd-uhs-sdr104;
>
> But I don't think it's necessary to lay out these slower modes
> explicitly, since SDR104 seems to imply them, see
> sd_update_bus_speed_mode() in drivers/mmc/core/sd.c[1],
>
> if ((card->host->caps & MMC_CAP_UHS_SDR104) &&
> (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_SDR104)) {
> card->sd_bus_speed = UHS_SDR104_BUS_SPEED;
> } else if ((card->host->caps & MMC_CAP_UHS_DDR50) &&
> (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_DDR50)) {
> card->sd_bus_speed = UHS_DDR50_BUS_SPEED;
> } else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
> MMC_CAP_UHS_SDR50)) && (card->sw_caps.sd3_bus_mode &
> SD_MODE_UHS_SDR50)) {
> card->sd_bus_speed = UHS_SDR50_BUS_SPEED;
> } else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
> MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR25)) &&
> (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_SDR25)) {
> card->sd_bus_speed = UHS_SDR25_BUS_SPEED;
> } else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
> MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR25 |
> MMC_CAP_UHS_SDR12)) && (card->sw_caps.sd3_bus_mode &
> SD_MODE_UHS_SDR12)) {
> card->sd_bus_speed = UHS_SDR12_BUS_SPEED;
> }
>
>> Thanks,
>> Chukun
>>
>> --
>> 2.25.1
>>
>
> Regards,
> Yao Zi
>
> [1]: https://elixir.bootlin.com/linux/v6.13.5/source/drivers/mmc/core/sd.c#L448-L479
