On 12/02/2025 20:56, Sebastian LaVine wrote: > > diff --git a/MAINTAINERS b/MAINTAINERS > index 27fb3c1be732..bf6a48da0887 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -21890,6 +21890,7 @@ M: Stuart Burtner <sburtner@xxxxxxxxxxxxxx> > L: linux-media@xxxxxxxxxxxxxxx > S: Odd Fixes > F: Documentation/devicetree/bindings/media/i2c/sony,imx728.yaml > +F: arch/arm64/boot/dts/ti/k3-am62a7-sk-fusion-2.dtso > F: drivers/media/i2c/imx728.c > > SONY MEMORYSTICK SUBSYSTEM > diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile > index f71360f14f23..fcd8d11e5678 100644 > --- a/arch/arm64/boot/dts/ti/Makefile > +++ b/arch/arm64/boot/dts/ti/Makefile > @@ -31,6 +31,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am62-lp-sk-nand.dtbo > # Boards with AM62Ax SoC > dtb-$(CONFIG_ARCH_K3) += k3-am62a7-sk.dtb > dtb-$(CONFIG_ARCH_K3) += k3-am62a7-phyboard-lyra-rdk.dtb > +dtb-$(CONFIG_ARCH_K3) += k3-am62a7-sk-fusion-2.dtbo I don't see the overlay being applied. > > # Boards with AM62Px SoC > dtb-$(CONFIG_ARCH_K3) += k3-am62p5-sk.dtb > diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk-fusion-2.dtso b/arch/arm64/boot/dts/ti/k3-am62a7-sk-fusion-2.dtso > new file mode 100644 > index 000000000000..68e06d643bfd > --- /dev/null > +++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk-fusion-2.dtso > @@ -0,0 +1,115 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * DT Overlay for Fusion 2 (FPD-Link IV) board on SK-AM62A > + * https://www.ti.com/tool/J7EXPAXEVM/ > + * > + * Copyright (C) 2024 D3 Embedded - https://www.d3embedded.com > + */ > + > + /dts-v1/; > + /plugin/; > + > +#include <dt-bindings/gpio/gpio.h> > + > +&{/} { > + clk_fusion2_25M_fixed: fixed-clock-25M { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <25000000>; > + }; > +}; > + > +&exp2 { > + p9-hog { > + /* P9 - CSI_RSTz */ > + gpio-hog; > + gpios = <9 GPIO_ACTIVE_HIGH>; > + output-high; > + line-name = "CSI_RSTz"; > + }; > + > + p19-hog { > + /* P19 -CSI_SEL2 */ > + gpio-hog; > + gpios = <19 GPIO_ACTIVE_HIGH>; > + output-low; > + line-name = "CSI_SEL2"; > + }; > +}; > + > +&main_i2c2 { > + #address-cells = <1>; > + #size-cells = <0>; > + status = "okay"; > + > + i2c-switch@71 { > + compatible = "nxp,pca9543"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x71>; reg is always the second property. See DTS coding style. Best regards, Krzysztof
