Add documentation for AD7191 driver. Signed-off-by: Alisa-Dariana Roman <alisa.roman@xxxxxxxxxx> --- Documentation/iio/ad7191.rst | 250 +++++++++++++++++++++++++++++++++++ Documentation/iio/index.rst | 1 + 2 files changed, 251 insertions(+) create mode 100644 Documentation/iio/ad7191.rst diff --git a/Documentation/iio/ad7191.rst b/Documentation/iio/ad7191.rst new file mode 100644 index 000000000000..b55f3c13e45a --- /dev/null +++ b/Documentation/iio/ad7191.rst @@ -0,0 +1,250 @@ +.. SPDX-License-Identifier: GPL-2.0-only + +============== +AD7191 driver +============== + +Device driver for Analog Devices AD7191 ADC. + +================== +Supported devices +================== + +* `AD7191 <https://www.analog.com/AD7191>`_ + +The AD7191 is a high precision, low noise, 24-bit Σ-Δ ADC with integrated PGA. +It features two differential input channels, an internal temperature sensor, and +configurable sampling rates. + +===================== +Device Configuration +===================== + +-------------------- +Pin Configuration +-------------------- + +The driver supports both pin-strapped and GPIO-controlled configurations for ODR +(Output Data Rate) and PGA (Programmable Gain Amplifier) settings. These +configurations are mutually exclusive - you must use either pin-strapped or GPIO +control for each setting, not both. + +^^^^^^^^^^^^^^^^^^^^ +ODR Configuration +^^^^^^^^^^^^^^^^^^^^ + +The ODR can be configured either through GPIO control or pin-strapping: + +- When using GPIO control, specify the "odr-gpios" property in the device tree +- For pin-strapped configuration, specify the "adi,odr-value" property in the + device tree + +Available ODR settings: + + - 120 Hz (ODR1=0, ODR2=0) + - 60 Hz (ODR1=0, ODR2=1) + - 50 Hz (ODR1=1, ODR2=0) + - 10 Hz (ODR1=1, ODR2=1) + +^^^^^^^^^^^^^^^^^^^ +PGA Configuration +^^^^^^^^^^^^^^^^^^^ + +The PGA can be configured either through GPIO control or pin-strapping: + +- When using GPIO control, specify the "pga-gpios" property in the device tree +- For pin-strapped configuration, specify the "adi,pga-value" property in the + device tree + +Available PGA gain settings: + + - 1x (PGA1=0, PGA2=0) + - 8x (PGA1=0, PGA2=1) + - 64x (PGA1=1, PGA2=0) + - 128x (PGA1=1, PGA2=1) + +-------------------- +Clock Configuration +-------------------- + +The AD7191 supports both internal and external clock sources: + +- When CLKSEL pin is tied LOW: Uses internal 4.92MHz clock (no clock property + needed) +- When CLKSEL pin is tied HIGH: Requires external clock source + - Can be a crystal between MCLK1 and MCLK2 pins + - Or a CMOS-compatible clock driving MCLK2 pin + - Must specify the "clocks" property in device tree when using external clock + +-------------------------- +SPI Interface Requirements +-------------------------- + +The AD7191 has specific SPI interface requirements: + +- The DOUT/RDY output is dual-purpose and requires SPI bus locking +- DOUT/RDY must be connected to an interrupt-capable GPIO +- The SPI controller's chip select must be connected to the PDOWN pin of the ADC +- When CS (PDOWN) is high, the device powers down and resets internal circuitry +- SPI mode 3 operation (CPOL=1, CPHA=1) is required + +------------------------- +Power Supply Requirements +------------------------- + +The device requires the following power supplies: + +- AVdd: Analog power supply +- DVdd: Digital power supply +- Vref: Reference voltage supply (external) + +All power supplies must be specified in the device tree. + +=================== +Device Attributes +=================== + +The AD7191 provides several attributes through the IIO sysfs interface: + +----------------------------------- +Voltage Input Differential Channels +----------------------------------- + ++-------------------+----------------------------------------------------------+ +| Attribute | Description | ++===================+==========================================================+ +| raw | Raw ADC output value | ++-------------------+----------------------------------------------------------+ +| scale | Scale factor to convert raw value to voltage | ++-------------------+----------------------------------------------------------+ +| offset | Voltage offset | ++-------------------+----------------------------------------------------------+ +| sampling_frequency| Current sampling frequency setting | ++-------------------+----------------------------------------------------------+ + +-------------------- +Temperature Sensor +-------------------- + ++-------------------+----------------------------------------------------------+ +| Attribute | Description | ++===================+==========================================================+ +| raw | Raw temperature sensor output value | ++-------------------+----------------------------------------------------------+ +| scale | Scale factor to convert raw value to temperature | ++-------------------+----------------------------------------------------------+ +| offset | Temperature calibration offset | ++-------------------+----------------------------------------------------------+ + +-------------------- +Available Attributes +-------------------- + +The following attributes show available configuration options: + +- sampling_frequency_available: List of supported sampling frequencies +- scale_available: List of supported scale factors (based on PGA settings) + +===================== +Channel Configuration +===================== + +The device provides three channels: + +1. Temperature Sensor + - 24-bit unsigned + - Internal temperature measurement + - Temperature in millidegrees Celsius + +2. Differential Input (AIN1-AIN2) + - 24-bit unsigned + - Differential voltage measurement + - Configurable gain via PGA + +3. Differential Input (AIN3-AIN4) + - 24-bit unsigned + - Differential voltage measurement + - Configurable gain via PGA + +===================== +Device Tree Bindings +===================== + +------------------- +Required Properties +------------------- + +- compatible: Should be "adi,ad7191" +- reg: SPI chip select number +- spi-max-frequency: Maximum SPI clock frequency +- spi-cpol: Must be present (set to 1) +- spi-cpha: Must be present (set to 1) +- interrupts: Interrupt mapping for DOUT/RDY pin +- avdd-supply: Analog power supply +- dvdd-supply: Digital power supply +- vref-supply: Reference voltage supply +- temp-gpios: GPIO for temperature channel selection +- chan-gpios: GPIO for input channel selection + +------------------- +Optional Properties +------------------- + +- clocks: Required when using external clock (CLKSEL=1), must be absent for + internal clock +- adi,odr-value: Pin-strapped ODR configuration (120, 60, 50, or 10) +- adi,pga-value: Pin-strapped PGA configuration (1, 8, 64, or 128) +- odr-gpios: GPIOs for ODR control (mutually exclusive with adi,odr-value) +- pga-gpios: GPIOs for PGA control (mutually exclusive with adi,pga-value) + +------------------- +Example Device Tree +------------------- + +.. code-block:: dts + + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + ad7191@0 { + compatible = "adi,ad7191"; + reg = <0>; + spi-max-frequency = <1000000>; + + /* Required SPI mode 3 */ + spi-cpol; + spi-cpha; + + /* Interrupt for DOUT/RDY pin */ + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio>; + + /* Power supplies */ + avdd-supply = <&avdd>; + dvdd-supply = <&dvdd>; + vref-supply = <&vref>; + + /* Optional external clock */ + clocks = <&ad7191_mclk>; + + /* Configuration - either use GPIO control or pin-strapped values */ + adi,pga-value = <1>; + odr-gpios = <&gpio 23 GPIO_ACTIVE_HIGH>, + <&gpio 24 GPIO_ACTIVE_HIGH>; + + /* Required GPIO controls */ + temp-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + chan-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>; + }; + }; + +================ +Buffer Support +================ + +This driver supports IIO triggered buffers. See Documentation/iio/iio_devbuf.rst +for more information about IIO triggered buffers. diff --git a/Documentation/iio/index.rst b/Documentation/iio/index.rst index 5710f5b9e958..9235f38f47a1 100644 --- a/Documentation/iio/index.rst +++ b/Documentation/iio/index.rst @@ -20,6 +20,7 @@ Industrial I/O Kernel Drivers ad4000 ad4695 + ad7191 ad7380 ad7606 ad7625 -- 2.43.0
