AD7191 is a pin-programmable, ultra-low noise 24-bit sigma-delta ADC designed for precision bridge sensor measurements. It features two differential analog input channels, selectable output rates, programmable gain, internal temperature sensor and simultaneous 50Hz/60Hz rejection. Signed-off-by: Alisa-Dariana Roman <alisa.roman@xxxxxxxxxx> --- .../bindings/iio/adc/adi,ad7191.yaml | 149 ++++++++++++++++++ MAINTAINERS | 7 + 2 files changed, 156 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7191.yaml diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7191.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7191.yaml new file mode 100644 index 000000000000..ac14096ba76c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7191.yaml @@ -0,0 +1,149 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2025 Analog Devices Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/adi,ad7191.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD7191 ADC + +maintainers: + - Alisa-Dariana Roman <alisa.roman@xxxxxxxxxx> + +description: | + Bindings for the Analog Devices AD7191 ADC device. Datasheet can be + found here: + https://www.analog.com/media/en/technical-documentation/data-sheets/AD7191.pdf + The device's PDOWN pin must be connected to the SPI controller's chip select + pin. + +properties: + compatible: + enum: + - adi,ad7191 + + reg: + maxItems: 1 + + spi-cpol: true + + spi-cpha: true + + clocks: + maxItems: 1 + description: | + Must be present when CLKSEL pin is tied HIGH to select external clock + source (either a crystal between MCLK1 and MCLK2 pins, or a + CMOS-compatible clock driving MCLK2 pin). Must be absent when CLKSEL pin + is tied LOW to use the internal 4.92MHz clock. + + interrupts: + maxItems: 1 + + avdd-supply: + description: AVdd voltage supply + + dvdd-supply: + description: DVdd voltage supply + + vref-supply: + description: Vref voltage supply + + odr-gpios: + description: | + ODR1 and ODR2 pins for output data rate selection. Should be defined if + adi,odr-value is absent. + minItems: 2 + maxItems: 2 + + adi,odr-value: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Should be present if ODR pins are pin-strapped. Possible values: + 120 Hz (ODR1=0, ODR2=0) + 60 Hz (ODR1=0, ODR2=1) + 50 Hz (ODR1=1, ODR2=0) + 10 Hz (ODR1=1, ODR2=1) + If defined, odr-gpios must be absent. + enum: [120, 60, 50, 10] + + pga-gpios: + description: | + PGA1 and PGA2 pins for gain selection. Should be defined if adi,pga-value + is absent. + minItems: 2 + maxItems: 2 + + adi,pga-value: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Should be present if PGA pins are pin-strapped. Possible values: + Gain 1 (PGA1=0, PGA2=0) + Gain 8 (PGA1=0, PGA2=1) + Gain 64 (PGA1=1, PGA2=0) + Gain 128 (PGA1=1, PGA2=1) + If defined, pga-gpios must be absent. + enum: [1, 8, 64, 128] + + temp-gpios: + description: TEMP pin for temperature sensor enable. + maxItems: 1 + + chan-gpios: + description: CHAN pin for input channel selection. + maxItems: 1 + +required: + - compatible + - reg + - interrupts + - avdd-supply + - dvdd-supply + - vref-supply + - spi-cpol + - spi-cpha + - temp-gpios + - chan-gpios + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + - oneOf: + - required: + - adi,odr-value + - required: + - odr-gpios + - oneOf: + - required: + - adi,pga-value + - required: + - pga-gpios + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/irq.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "adi,ad7191"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + spi-cpha; + clocks = <&ad7191_mclk>; + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio>; + avdd-supply = <&avdd>; + dvdd-supply = <&dvdd>; + vref-supply = <&vref>; + adi,pga-value = <1>; + odr-gpios = <&gpio 23 GPIO_ACTIVE_HIGH>, <&gpio 24 GPIO_ACTIVE_HIGH>; + temp-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + chan-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/MAINTAINERS b/MAINTAINERS index 98a3c1e46311..262beced3143 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1302,6 +1302,13 @@ W: http://ez.analog.com/community/linux-device-drivers F: Documentation/devicetree/bindings/iio/adc/adi,ad7091r* F: drivers/iio/adc/ad7091r* +ANALOG DEVICES INC AD7191 DRIVER +M: Alisa-Dariana Roman <alisa.roman@xxxxxxxxxx> +L: linux-iio@xxxxxxxxxxxxxxx +S: Supported +W: https://ez.analog.com/linux-software-drivers +F: Documentation/devicetree/bindings/iio/adc/adi,ad7191.yaml + ANALOG DEVICES INC AD7192 DRIVER M: Alisa-Dariana Roman <alisa.roman@xxxxxxxxxx> L: linux-iio@xxxxxxxxxxxxxxx -- 2.43.0
