Re: [PATCH v6 0/3] Add support for Ariaboard Photonicat RK3568

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2025/1/12 16:50, Dragan Simic wrote:
> Hello Junhao,
> 
> On 2025-01-12 08:33, Junhao Xie wrote:
>> Add dts for Ariaboard Photonicat RK3568.
>>
>> This series bring support for:
>> * Debug UART
>> * SDIO QCA9377 WiFi and Bluetooth
>> * M.2 E-Key PCIe WiFi and Bluetooth
>> * M.2 B-Key USB Modem WWAN
>> * Ethernet WAN Port
>> * MicroSD Card slot
>> * eMMC
>> * HDMI Output
>> * Mali GPU
>> * USB Type-A
>>
>> Changed from v1:
>> - move some general nodes (firmware, ramoops, reboot-mode) to rk356x.dtsi
> 
> This entry from the changelog caught my attention, so I tried
> to find out what exactly happened back then.  Though, after going
> through the mailing list archive, I still don't see where the
> as-described change took place, so perhaps this changelog entry
> needs adjusting.

Chukun Pan suggested moving these nodes to rk356x.dtsi, but I have not done
that yet and simply deleted them. I will fix the changelog.
https://lore.kernel.org/lkml/20240905034009.28124-1-amadeus@xxxxxxxxxx/

- remove some general nodes (firmware, ramoops, reboot-mode)

> 
>> - gmac1 change to phy-mode rgmii-id
>> - corrected some regulator to be closer to schematics
>> - rename rk3568-ariaboard-photonicat.dts to rk3568-photonicat.dts
>> https://lore.kernel.org/lkml/20240904111456.87089-1-bigfoot@xxxxxxxxxxx/
>>
>> Changed from v2:
>> - remove unused headers
>> - corrected some regulator to be closer to schematics
>> - remove usb_host1_ohci, usb_host1_ehci, usb2phy1_host that have no connection
>> https://lore.kernel.org/lkml/20240906045706.1004813-1-bigfoot@xxxxxxxxxxx/
>>
>> Changed from v3:
>> - corrected some regulator to be closer to schematics
>> - changed to using clk32k_out1 in xin32k
>> https://lore.kernel.org/lkml/20240911122809.1789778-2-bigfoot@xxxxxxxxxxx/
>>
>> Changed from v4:
>> - corrected some regulator to be closer to schematics
>> - corrected some label to match node name
>> - use resets props in phy node instead deprecated snps,reset-gpio
>> https://lore.kernel.org/lkml/20240914145549.879936-1-bigfoot@xxxxxxxxxxx/
>>
>> Changed from v5:
>> - resort regulator nodes
>> - remove dr_mode from usb_host1_xhci
>> https://lore.kernel.org/lkml/20241108031847.700606-1-bigfoot@xxxxxxxxxxx/
>>
>> Junhao Xie (3):
>>   dt-bindings: vendor-prefixes: Add prefix for Ariaboard
>>   dt-bindings: arm: rockchip: Add Ariaboard Photonicat RK3568
>>   arm64: dts: rockchip: add dts for Ariaboard Photonicat RK3568
>>
>>  .../devicetree/bindings/arm/rockchip.yaml     |   5 +
>>  .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
>>  arch/arm64/boot/dts/rockchip/Makefile         |   1 +
>>  .../boot/dts/rockchip/rk3568-photonicat.dts   | 599 ++++++++++++++++++
>>  4 files changed, 607 insertions(+)
>>  create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts

Thanks for your review, I will fix all problems in next version!

Best regards,
Junhao





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux