Re: [PATCH v2 2/2] arm64: dts: allwinner: a64: Add WiFi/BT header on SoPine

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Dec 20, 2024 at 8:00 PM Peter Robinson <pbrobinson@xxxxxxxxx> wrote:
>
> This adds all the pin mappings on the WiFi/BT header on
> the SoPine baseboard/A64-LTS. They're disabled by default
> as the modules don't ship by default. This includes, where
> they haven't been already, UART1 for BT and mmc1 for WiFi.
>
> Signed-off-by: Peter Robinson <pbrobinson@xxxxxxxxx>
> ---
>  .../allwinner/sun50i-a64-sopine-baseboard.dts | 24 +++++++++++++++++++
>  1 file changed, 24 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
> index be2347c8f267..752d2aae8465 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
> @@ -42,6 +42,11 @@ reg_vcc1v8: vcc1v8 {
>                 regulator-min-microvolt = <1800000>;
>                 regulator-max-microvolt = <1800000>;
>         };
> +
> +       wifi_pwrseq: pwrseq {
> +               compatible = "mmc-pwrseq-simple";
> +               reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
> +       };
>  };
>
>  &ac_power_supply {
> @@ -103,6 +108,17 @@ ext_rgmii_phy: ethernet-phy@1 {
>         };
>  };
>
> +/* On Wifi/BT connector */
> +&mmc1 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&mmc1_pins>;
> +       vmmc-supply = <&reg_dldo4>;
> +       vqmmc-supply = <&reg_eldo1>;
> +       mmc-pwrseq = <&wifi_pwrseq>;
> +       bus-width = <4>;
> +       non-removable;

Same here, please explicitly set 'status = "disabled"' like what
you are doing with uart1 below.

ChenYu

> +};
> +
>  &mmc2 {
>         pinctrl-names = "default";
>         pinctrl-0 = <&mmc2_pins>;
> @@ -175,6 +191,14 @@ &uart0 {
>         status = "okay";
>  };
>
> +/* On Wifi/BT connector, with RTS/CTS */
> +&uart1 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> +       uart-has-rtscts;
> +       status = "disabled";
> +};
> +
>  /* On Pi-2 connector */
>  &uart2 {
>         pinctrl-names = "default";
> --
> 2.47.1
>
>





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux