From: Frieder Schrempf <frieder.schrempf@xxxxxxxxxx> This is a follow-up of [1]. The main objective of this is to fix the PCA9450 driver to use the correct control register for the LDO5 regulator. Currently the control register to use for LDO5 is hardcoded to LDO5CTRL_H. This is wrong for two reasons: 1. LDO5CTRL_H doesn't contain the bits for enabling/disabling the regulator. Only LDO5CTRL_L does. 2. The actual output voltage of the regulator is determined by the LDO5CTRL_H only if the SD_VSEL input is HIGH. If it is low, then LDO5CTRL_L is used. The driver does not take this into account. This can cause several problems: 1. LDO5 can not be turned on/off and we rely on the bootloader to leave it turned on. On the other hand we can't save power if LDO5 is unused. 2. There is a potential for corner-cases where switching SD_VSEL via USDHC_VSELECT and writing to the (wrong) control register can cause wrong output voltage and therfore SD card failures (not observed yet). 3. Reading the current voltage of the LDO5 regulator (e. g. via sysfs can yield the wrong value as the voltage is read from the wrong control register. At the same time there is now hardware that hardwires SD_VSEL to a fixed LOW level and therefore relies on switching the voltage only via a single control register. We add support for this through an additional property "nxp,sd-vsel-fixed-low" in the LDO5 node. Summary of binding changes (patch 1-3): 1. Adjust the bindings to remove the old and abandoned use of sd-vsel-gpios property. 2. Adjust the bindings to use sd-vsel-gpios in the LDO5 node to retrieve an input that can be used to sample the SD_VSEL status. 3. Adjust bindings to allow "nxp,sd-vsel-fixed-low" to be used for boards that have SD_VSEL hardwired to low level. Summary of driver changes (patch 4-7): 1. Remove the old sd-vsel-gpios handling. 2. Use the new sd-vsel-gpios property to determine the correct control register for LDO5. 3. Fix the enable register for LDO5. 4. Support hardware with fixed low level of SD_VSEL. Summary of devicetree changes (patch 8-10): Implement the changes in the devicetrees for Kontron hardware (i.MX8MM, i.MX8MP and i.MX93). Changelog: v1 -> v2: * Split binding patch * Add solution for hardwired SD_VSEL * Leave regulator core untouched as requested by Mark * Add devicetree changes for i.MX8MP and i.MX93 [1] https://lore.kernel.org/lkml/20230213155833.1644366-1-frieder@xxxxxxx/ Frieder Schrempf (11): Revert "regulator: pca9450: Add sd-vsel GPIO" dt-bindings: regulator: pca9450: Add sd-vsel-gpios to read back LDO5 status dt-bindings: regulator: pca9450: Document nxp,sd-vsel-fixed-low property for LDO5 arm64: dts: imx8mp-skov-reva: Use hardware signal for SD card VSELECT Revert "regulator: pca9450: Add SD_VSEL GPIO for LDO5" regulator: pca9450: Fix control register for LDO5 regulator: pca9450: Fix enable register for LDO5 regulator: pca9450: Handle hardware with fixed SD_VSEL for LDO5 arm64: dts: imx8mm-kontron: Add support for reading SD_VSEL signal arm64: dts: imx93-kontron: Fix SD card IO voltage control arm64: dts: imx8mp-kontron: Add support for reading SD_VSEL signal .../regulator/nxp,pca9450-regulator.yaml | 29 ++++-- .../boot/dts/freescale/imx8mm-kontron-bl.dts | 10 ++- .../dts/freescale/imx8mm-kontron-osm-s.dtsi | 7 +- .../dts/freescale/imx8mp-kontron-osm-s.dtsi | 7 +- .../boot/dts/freescale/imx8mp-skov-reva.dtsi | 5 +- .../dts/freescale/imx93-kontron-osm-s.dtsi | 5 +- drivers/regulator/pca9450-regulator.c | 88 ++++++++++++++++--- 7 files changed, 119 insertions(+), 32 deletions(-) -- 2.46.1
