Add device tree bindings for the gpio/pin/mux controller that is part of the RP1 multi function device, and relative entries in MAINTAINERS file. Signed-off-by: Andrea della Porta <andrea.porta@xxxxxxxx> --- .../pinctrl/raspberrypi,rp1-gpio.yaml | 193 ++++++++++++++++++ MAINTAINERS | 2 + 2 files changed, 195 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/raspberrypi,rp1-gpio.yaml diff --git a/Documentation/devicetree/bindings/pinctrl/raspberrypi,rp1-gpio.yaml b/Documentation/devicetree/bindings/pinctrl/raspberrypi,rp1-gpio.yaml new file mode 100644 index 000000000000..21923d39c1bc --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/raspberrypi,rp1-gpio.yaml @@ -0,0 +1,193 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/raspberrypi,rp1-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RaspberryPi RP1 GPIO/Pinconf/Pinmux Controller submodule + +maintainers: + - Andrea della Porta <andrea.porta@xxxxxxxx> + +description: + The RP1 chipset is a Multi Function Device containing, among other + sub-peripherals, a gpio/pinconf/mux controller whose 54 pins are grouped + into 3 banks. + It works also as an interrupt controller for those gpios. + +properties: + compatible: + const: raspberrypi,rp1-gpio + + reg: + maxItems: 3 + description: One reg specifier for each one of the 3 pin banks. + + '#gpio-cells': + description: The first cell is the pin number and the second cell is used + to specify the flags (see include/dt-bindings/gpio/gpio.h). + const: 2 + + gpio-controller: true + + gpio-ranges: + maxItems: 1 + + gpio-line-names: + maxItems: 54 + + interrupts: + maxItems: 3 + description: One interrupt specifier for each one of the 3 pin banks. + + '#interrupt-cells': + description: + Specifies the Bank number [0, 1, 2] and Flags as defined in + include/dt-bindings/interrupt-controller/irq.h. + const: 2 + + interrupt-controller: true + +patternProperties: + "-state$": + oneOf: + - $ref: "#/$defs/raspberrypi-rp1-state" + - patternProperties: + "-pins$": + $ref: "#/$defs/raspberrypi-rp1-state" + additionalProperties: false + +$defs: + raspberrypi-rp1-state: + allOf: + - $ref: pincfg-node.yaml# + - $ref: pinmux-node.yaml# + + description: + Pin controller client devices use pin configuration subnodes (children + and grandchildren) for desired pin configuration. + Client device subnodes use below standard properties. + + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + pattern: "^gpio([0-9]|[1-5][0-9])$" + + function: + enum: [ alt0, alt1, alt2, alt3, alt4, gpio, alt6, alt7, alt8, none, + aaud, dcd0, dpi, dsi0_te_ext, dsi1_te_ext, dsr0, dtr0, gpclk0, + gpclk1, gpclk2, gpclk3, gpclk4, gpclk5, i2c0, i2c1, i2c2, i2c3, + i2c4, i2c5, i2c6, i2s0, i2s1, i2s2, ir, mic, pcie_clkreq_n, + pio, proc_rio, pwm0, pwm1, ri0, sd0, sd1, spi0, spi1, spi2, + spi3, spi4, spi5, spi6, spi7, spi8, uart0, uart1, uart2, uart3, + uart4, uart5, vbus0, vbus1, vbus2, vbus3 ] + + description: + Specify the alternative function to be configured for the specified + pins. + + bias-disable: true + bias-pull-down: true + bias-pull-up: true + slew-rate: + description: 0 is slow slew rate, 1 is fast slew rate + enum: [ 0, 1 ] + drive-strength: + enum: [ 2, 4, 8, 12 ] + + additionalProperties: false + +allOf: + - $ref: pinctrl.yaml# + +required: + - reg + - compatible + - '#gpio-cells' + - gpio-controller + - interrupts + - '#interrupt-cells' + - interrupt-controller + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + rp1 { + #address-cells = <2>; + #size-cells = <2>; + + rp1_gpio: pinctrl@c0400d0000 { + reg = <0xc0 0x400d0000 0x0 0xc000>, + <0xc0 0x400e0000 0x0 0xc000>, + <0xc0 0x400f0000 0x0 0xc000>; + compatible = "raspberrypi,rp1-gpio"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, + <1 IRQ_TYPE_LEVEL_HIGH>, + <2 IRQ_TYPE_LEVEL_HIGH>; + gpio-line-names = + "ID_SDA", // GPIO0 + "ID_SCL", // GPIO1 + "GPIO2", "GPIO3", "GPIO4", "GPIO5", "GPIO6", + "GPIO7", "GPIO8", "GPIO9", "GPIO10", "GPIO11", + "GPIO12", "GPIO13", "GPIO14", "GPIO15", "GPIO16", + "GPIO17", "GPIO18", "GPIO19", "GPIO20", "GPIO21", + "GPIO22", "GPIO23", "GPIO24", "GPIO25", "GPIO26", + "GPIO27", + "PCIE_RP1_WAKE", // GPIO28 + "FAN_TACH", // GPIO29 + "HOST_SDA", // GPIO30 + "HOST_SCL", // GPIO31 + "ETH_RST_N", // GPIO32 + "", // GPIO33 + "CD0_IO0_MICCLK", // GPIO34 + "CD0_IO0_MICDAT0", // GPIO35 + "RP1_PCIE_CLKREQ_N", // GPIO36 + "", // GPIO37 + "CD0_SDA", // GPIO38 + "CD0_SCL", // GPIO39 + "CD1_SDA", // GPIO40 + "CD1_SCL", // GPIO41 + "USB_VBUS_EN", // GPIO42 + "USB_OC_N", // GPIO43 + "RP1_STAT_LED", // GPIO44 + "FAN_PWM", // GPIO45 + "CD1_IO0_MICCLK", // GPIO46 + "2712_WAKE", // GPIO47 + "CD1_IO1_MICDAT1", // GPIO48 + "EN_MAX_USB_CUR", // GPIO49 + "", // GPIO50 + "", // GPIO51 + "", // GPIO52 + ""; // GPIO53 + + rp1-i2s0-default-state { + function = "i2s0"; + pins = "gpio18", "gpio19", "gpio20", "gpio21"; + bias-disable; + }; + + rp1-uart0-default-state { + txd-pins { + function = "uart0"; + pins = "gpio14"; + bias-disable; + }; + + rxd-pins { + function = "uart0"; + pins = "gpio15"; + bias-pull-up; + }; + }; + }; + }; diff --git a/MAINTAINERS b/MAINTAINERS index 75a66e3e34c9..c55d12550246 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -19384,7 +19384,9 @@ RASPBERRY PI RP1 PCI DRIVER M: Andrea della Porta <andrea.porta@xxxxxxxx> S: Maintained F: Documentation/devicetree/bindings/clock/raspberrypi,rp1-clocks.yaml +F: Documentation/devicetree/bindings/pinctrl/raspberrypi,rp1-gpio.yaml F: include/dt-bindings/clock/rp1.h +F: include/dt-bindings/misc/rp1.h RC-CORE / LIRC FRAMEWORK M: Sean Young <sean@xxxxxxxx> -- 2.35.3
