On 11/15/2024 6:58 AM, Dmitry Baryshkov wrote:
On Mon, Nov 11, 2024 at 04:49:32PM -0800, Melody Olvera wrote:
From: Jishnu Prakash <quic_jprakash@xxxxxxxxxxx>
Add descriptions of pmd8028 and pmih0108 PMICs used on SM8750
platforms.
Up/lower case?
Up; will change.
Signed-off-by: Jishnu Prakash <quic_jprakash@xxxxxxxxxxx>
Signed-off-by: Melody Olvera <quic_molvera@xxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/pmd8028.dtsi | 56 +++++++++++++++++++++++
arch/arm64/boot/dts/qcom/pmih0108.dtsi | 62 ++++++++++++++++++++++++++
Those two are independent changes. Please use two separate patches.
Sure thing. Will split.
2 files changed, 118 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pmd8028.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/pmih0108.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pmd8028.dtsi b/arch/arm64/boot/dts/qcom/pmd8028.dtsi
new file mode 100644
index 000000000000..f8ef8e133854
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmd8028.dtsi
@@ -0,0 +1,56 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+ thermal-zones {
+ pmd8028-thermal {
+ polling-delay-passive = <100>;
+ thermal-sensors = <&pmd8028_temp_alarm>;
+
+ trips {
+ pmd8028_trip0: trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ pmd8028_trip1: trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
"critical" ?
Will add.
+ };
+ };
+ };
+ };
+};
+
+&spmi_bus {
+ pmd8028: pmic@4 {
+ compatible = "qcom,pmd8028", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmd8028_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmd8028_gpios: gpio@8800 {
+ compatible = "qcom,pmd8028-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmd8028_gpios 0 0 4>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/pmih0108.dtsi b/arch/arm64/boot/dts/qcom/pmih0108.dtsi
new file mode 100644
index 000000000000..3907d8fbcf78
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmih0108.dtsi
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+ thermal-zones {
+ pmih0108-thermal {
+ polling-delay-passive = <100>;
+ thermal-sensors = <&pmih0108_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
"critical" ?
Will add.
Thanks,
Melody
+ };
+ };
+ };
+ };
+};
+[...]
