On Thu, Nov 14, 2024 at 05:54:08PM +0800, Ziyue Zhang wrote:
> Add configurations in devicetree for PCIe0, including registers, clocks,
> interrupts and phy setting sequence.
>
> Signed-off-by: Ziyue Zhang <quic_ziyuzhan@xxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/qcs8300-ride.dts | 44 +++++-
> arch/arm64/boot/dts/qcom/qcs8300.dtsi | 176 ++++++++++++++++++++++
> 2 files changed, 219 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
> index 7eed19a694c3..9d7c8555ed38 100644
> --- a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
> +++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
> @@ -213,7 +213,7 @@ vreg_l9c: ldo9 {
> &gcc {
The patch doesn't seem to update the gcc node in qcs8300.dtsi. Is there
any reason to have the clocks property in the board data file?
> clocks = <&rpmhcc RPMH_CXO_CLK>,
> <&sleep_clk>,
> - <0>,
> + <&pcie0_phy>,
> <0>,
> <0>,
> <0>,
> @@ -223,6 +223,23 @@ &gcc {
> <0>;
> };
>
> +&pcie0 {
> + perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
> + wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
> +
> + pinctrl-0 = <&pcie0_default_state>;
> + pinctrl-names = "default";
> +
> + status = "okay";
> +};
> +
> +&pcie0_phy {
> + vdda-phy-supply = <&vreg_l6a>;
> + vdda-pll-supply = <&vreg_l5a>;
> +
> + status = "okay";
> +};
> +
> &qupv3_id_0 {
> status = "okay";
> };
> @@ -247,6 +264,31 @@ &rpmhcc {
> clock-names = "xo";
> };
>
> +&tlmm {
> + pcie0_default_state: pcie0-default-state {
> + perst-pins {
> + pins = "gpio2";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + clkreq-pins {
> + pins = "gpio1";
> + function = "pcie0_clkreq";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + wake-pins {
> + pins = "gpio0";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> + };
> +};
> +
> &uart7 {
> status = "okay";
> };
> diff --git a/arch/arm64/boot/dts/qcom/qcs8300.dtsi b/arch/arm64/boot/dts/qcom/qcs8300.dtsi
> index 2c35f96c3f28..d4924f48b347 100644
> --- a/arch/arm64/boot/dts/qcom/qcs8300.dtsi
> +++ b/arch/arm64/boot/dts/qcom/qcs8300.dtsi
> @@ -637,6 +637,182 @@ mmss_noc: interconnect@17a0000 {
> qcom,bcm-voters = <&apps_bcm_voter>;
> };
>
> + pcie0: pci@1c00000 {
> + compatible = "qcom,pcie-qcs8300","qcom,pcie-sa8775p";
> + reg = <0x0 0x01c00000 0x0 0x3000>,
> + <0x0 0x40000000 0x0 0xf20>,
> + <0x0 0x40000f20 0x0 0xa8>,
> + <0x0 0x40001000 0x0 0x4000>,
> + <0x0 0x40100000 0x0 0x100000>,
> + <0x0 0x01c03000 0x0 0x1000>;
> +
> + reg-names = "parf",
> + "dbi",
> + "elbi",
> + "atu",
> + "config",
> + "mhi";
> +
> + device_type = "pci";
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x100000>,
> + <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
> + bus-range = <0x00 0xff>;
> +
> + dma-coherent;
> +
> + linux,pci-domain = <0>;
> + num-lanes = <2>;
> +
> + interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>;
> +
> + interrupt-names = "msi0",
> + "msi1",
> + "msi2",
> + "msi3",
> + "msi4",
> + "msi5",
> + "msi6",
> + "msi7";
> +
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc GIC_SPI 434 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &intc GIC_SPI 435 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &intc GIC_SPI 438 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &intc GIC_SPI 439 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
> + <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
> + <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
> + <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>;
> +
> + clock-names = "aux",
> + "cfg",
> + "bus_master",
> + "bus_slave",
> + "slave_q2a";
> +
> + assigned-clocks = <&gcc GCC_PCIE_0_AUX_CLK>;
> + assigned-clock-rates = <19200000>;
> +
> + interconnects = <&pcie_anoc MASTER_PCIE_0 0 &mc_virt SLAVE_EBI1 0>,
> + <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_PCIE_0 0>;
> +
> + interconnect-names = "pcie-mem", "cpu-pcie";
> +
> + iommu-map = <0x0 &pcie_smmu 0x0000 0x1>,
> + <0x100 &pcie_smmu 0x0001 0x1>;
> +
> + resets = <&gcc GCC_PCIE_0_BCR>;
> + reset-names = "pci";
> + power-domains = <&gcc GCC_PCIE_0_GDSC>;
> +
> + phys = <&pcie0_phy>;
> + phy-names = "pciephy";
> +
> + status = "disabled";
> +
> + pcie3_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + /* GEN 1 x1 */
> + opp-2500000 {
> + opp-hz = /bits/ 64 <2500000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + opp-peak-kBps = <250000 1>;
> + };
> +
> + /* GEN 1 x2 and GEN 2 x1 */
> + opp-5000000 {
> + opp-hz = /bits/ 64 <5000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + opp-peak-kBps = <500000 1>;
> + };
> +
> + /* GEN 2 x2 */
> + opp-10000000 {
> + opp-hz = /bits/ 64 <10000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + opp-peak-kBps = <1000000 1>;
> + };
> +
> + /* GEN 3 x1 */
> + opp-8000000 {
> + opp-hz = /bits/ 64 <8000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + opp-peak-kBps = <984500 1>;
> + };
> +
> + /* GEN 3 x2 and GEN 4 x1 */
> + opp-16000000 {
> + opp-hz = /bits/ 64 <16000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <1969000 1>;
> + };
> +
> + /* GEN 4 x2 */
> + opp-32000000 {
> + opp-hz = /bits/ 64 <32000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + opp-peak-kBps = <3938000 1>;
> + };
> + };
> +
> + pcieport0: pcie@0 {
> + device_type = "pci";
> + reg = <0x0 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges;
> + bus-range = <0x01 0xff>;
> + };
> + };
> +
> + pcie0_phy: phy@1c04000 {
> + compatible = "qcom,qcs8300-qmp-gen4x2-pcie-phy";
> + reg = <0x0 0x1c04000 0x0 0x2000>;
> +
> + clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
> + <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_CLKREF_EN>,
> + <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>,
> + <&gcc GCC_PCIE_0_PIPE_CLK>,
> + <&gcc GCC_PCIE_0_PIPEDIV2_CLK>,
> + <&gcc GCC_PCIE_0_PHY_AUX_CLK>;
> +
> + clock-names = "aux",
> + "cfg_ahb",
> + "ref",
> + "rchng",
> + "pipe",
> + "pipediv2",
> + "phy_aux";
> +
> + assigned-clocks = <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>;
> + assigned-clock-rates = <100000000>;
> +
> + resets = <&gcc GCC_PCIE_0_PHY_BCR>;
> + reset-names = "phy";
> +
> + #clock-cells = <0>;
> + clock-output-names = "pcie_0_pipe_clk";
> +
> + #phy-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> ufs_mem_hc: ufs@1d84000 {
> compatible = "qcom,qcs8300-ufshc", "qcom,ufshc", "jedec,ufs-2.0";
> reg = <0x0 0x01d84000 0x0 0x3000>;
> --
> 2.34.1
>
--
With best wishes
Dmitry
