From: Yangtao Li <frank@xxxxxxxxxxxxxxxxx> The A100 has 3 MMC controllers, one of them being especially targeted to eMMC. Let's add nodes on dts. Signed-off-by: Yangtao Li <frank@xxxxxxxxxxxxxxxxx> Reviewed-by: Andre Przywara <andre.przywara@xxxxxxx> Signed-off-by: Cody Eksal <masterr3c0rd@epochal.quest> --- .../arm64/boot/dts/allwinner/sun50i-a100.dtsi | 71 +++++++++++++++++++ 1 file changed, 71 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi index f6162a107641..29ac7716c7a5 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi @@ -169,12 +169,83 @@ pio: pinctrl@300b000 { interrupt-controller; #interrupt-cells = <3>; + mmc0_pins: mmc0-pins { + pins = "PF0", "PF1", "PF2", "PF3", + "PF4", "PF5"; + function = "mmc0"; + drive-strength = <30>; + bias-pull-up; + }; + + /omit-if-no-ref/ + mmc1_pins: mmc1-pins { + pins = "PG0", "PG1", "PG2", "PG3", + "PG4", "PG5"; + function = "mmc1"; + drive-strength = <30>; + bias-pull-up; + }; + + mmc2_pins: mmc2-pins { + pins = "PC0", "PC1", "PC5", "PC6", + "PC8", "PC9", "PC10", "PC11", + "PC13", "PC14", "PC15", "PC16"; + function = "mmc2"; + drive-strength = <30>; + bias-pull-up; + }; + uart0_pb_pins: uart0-pb-pins { pins = "PB9", "PB10"; function = "uart0"; }; }; + mmc0: mmc@4020000 { + compatible = "allwinner,sun50i-a100-mmc"; + reg = <0x04020000 0x1000>; + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC0>; + reset-names = "ahb"; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc1: mmc@4021000 { + compatible = "allwinner,sun50i-a100-mmc"; + reg = <0x04021000 0x1000>; + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC1>; + reset-names = "ahb"; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc2: mmc@4022000 { + compatible = "allwinner,sun50i-a100-emmc"; + reg = <0x04022000 0x1000>; + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC2>; + reset-names = "ahb"; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + uart0: serial@5000000 { compatible = "snps,dw-apb-uart"; reg = <0x05000000 0x400>; -- 2.47.0