On 28/10/2024 11:41, Heiko Schocher wrote:
> Hello Krzysztof,
>
> On 28.10.24 11:24, Krzysztof Kozlowski wrote:
>> On 28/10/2024 09:23, Heiko Schocher wrote:
>>> Add support for the i.MX8MP based aristainetos3 boards from ABB.
>>>
>>> The board uses a ABB specific SoM from ADLink, based on NXP
>>> i.MX8MP SoC. The SoM is used on 3 different carrier boards,
>>> with small differences, which are all catched up in
>>> devicetree overlays. The kernel image, the basic dtb
>>> and all dtbos are collected in a fitimage. As bootloader
>>> is used U-Boot which detects in his SPL stage the carrier
>>> board by probing some i2c devices. When the correct
>>> carrier is probed, the SPL applies all needed dtbos to
>>> the dtb with which U-Boot gets loaded. Same principle
>>> later before linux image boot, U-Boot applies the dtbos
>>> needed for the carrier board before booting Linux.
>>>
>>> Signed-off-by: Heiko Schocher <hs@xxxxxxx>
>>> ---
>>> checkpatch dropped the following warnings:
>>> arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi:248: warning: DT compatible string "ethernet-phy-id2000.a231" appears un-documented -- check ./Documentation/devicetree/bindings/
>>>
>>> ignored, as this compatible string is usedin other dts too, for example in
>>>
>>> arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi
>>>
>>> arch/arm64/boot/dts/freescale/Makefile | 5 +
>>> .../imx8mp-aristainetos3-adpismarc.dtsi | 64 +
>>> .../imx8mp-aristainetos3-adpismarc.dtso | 14 +
>>> .../imx8mp-aristainetos3-helios-lvds.dtsi | 89 ++
>>> .../imx8mp-aristainetos3-helios-lvds.dtso | 13 +
>>> .../imx8mp-aristainetos3-helios.dtsi | 103 ++
>>> .../imx8mp-aristainetos3-helios.dtso | 13 +
>>> .../imx8mp-aristainetos3-proton2s.dtsi | 176 +++
>>> .../imx8mp-aristainetos3-proton2s.dtso | 13 +
>>> .../imx8mp-aristainetos3a-som-v1.dts | 18 +
>>> .../imx8mp-aristainetos3a-som-v1.dtsi | 1210 +++++++++++++++++
>>> 11 files changed, 1718 insertions(+)
>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi
>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtso
>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtsi
>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios-lvds.dtso
>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtsi
>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-helios.dtso
>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtsi
>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-proton2s.dtso
>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dts
>>> create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-aristainetos3a-som-v1.dtsi
>>>
>>> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
>>> index 9d3df8b218a2..7c3586509b8b 100644
>>> --- a/arch/arm64/boot/dts/freescale/Makefile
>>> +++ b/arch/arm64/boot/dts/freescale/Makefile
>>> @@ -163,6 +163,11 @@ imx8mn-tqma8mqnl-mba8mx-usbotg-dtbs += imx8mn-tqma8mqnl-mba8mx.dtb imx8mn-tqma8m
>>> dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-lvds-tm070jvhg33.dtb
>>> dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx-usbotg.dtb
>>>
>>> +dtb-$(CONFIG_ARCH_MXC) += imx8mp-aristainetos3a-som-v1.dtb \
>>> + imx8mp-aristainetos3-adpismarc.dtbo \
>>> + imx8mp-aristainetos3-proton2s.dtbo \
>>> + imx8mp-aristainetos3-helios.dtbo \
>>> + imx8mp-aristainetos3-helios-lvds.dtbo
>>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-beacon-kit.dtb
>>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-data-modul-edm-sbc.dtb
>>> dtb-$(CONFIG_ARCH_MXC) += imx8mp-debix-model-a.dtb
>>> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi
>>> new file mode 100644
>>> index 000000000000..cc0cddaa33ea
>>> --- /dev/null
>>> +++ b/arch/arm64/boot/dts/freescale/imx8mp-aristainetos3-adpismarc.dtsi
>>> @@ -0,0 +1,64 @@
>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>>> +/*
>>> + * Copyright (C) 2024 Heiko Schocher <hs@xxxxxxx>
>>> + */
>>> +
>>> +#include <dt-bindings/gpio/gpio.h>
>>> +#include <dt-bindings/interrupt-controller/irq.h>
>>> +
>>> +&ecspi1 {
>>> + spidev0: spi@0 {
>>> + reg = <0>;
>>> + compatible = "rohm,dh2228fv";
>>
>> Hm? I have some doubts, what device is here?
>
> $ grep -lr dh2228fv drivers/
> drivers/spi/spidev.c
>
> Customer uses an userspace implementation...
That's not the question. I asked what device is here.
>
>>
>>> + spi-max-frequency = <500000>;
>>> + };
>>> +};
>>> +
>>> +&ecspi2 {
>>> + spidev1: spi@0 {
>>> + reg = <0>;
>>> + compatible = "rohm,dh2228fv";
>>> + spi-max-frequency = <500000>;
>>> + };
>>> +};
>>> +
>>> +&i2c2 {
>>> + /* SX1509(2) U1001@IPi SMARC Plus */
>>> + gpio8: i2c2_gpioext0@3e {
>>
>> Uh, no, please never send us downstream code.
>>
>> Please follow DTS coding style in all upstream submissions.
>
> driver is in here:
>
> $ grep -lr probe-reset drivers/pinctrl/
> drivers/pinctrl/pinctrl-sx150x.c
This so not related... Your driver does not matter. You send us poor
quality downstream code.
...
>
>> And why this is DTSO, I have no clue...
Why is this a DTSO, not a DTS?
Best regards,
Krzysztof
