Adding bootph properties on leaf nodes imply that they are applicable to
the parent nodes as well. Bootloaders can derive the parent nodes when
bootph is available in the leaf nodes.
Remove the bootph-* properties from parent nodes as they are redundant.
Reviewed-by: Aniket Limaye <a-limaye@xxxxxx>
Signed-off-by: Manorit Chawdhry <m-chawdhry@xxxxxx>
---
Notes:
R-by picked up in v5 ( Aniket )
arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi | 9 ---------
1 file changed, 9 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
index 98453171a1790cd605d25ad939f556127519524a..b2e2b9f507a9828d49b1eb94d098b2c6682cef0e 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
@@ -305,7 +305,6 @@ &wkup_gpio0 {
};
&main_pmx0 {
- bootph-all;
main_cpsw2g_default_pins: main-cpsw2g-default-pins {
pinctrl-single,pins = <
J784S4_IOPAD(0x0b8, PIN_INPUT, 6) /* (AC34) MCASP1_ACLKX.RGMII1_RD0 */
@@ -432,7 +431,6 @@ J784S4_IOPAD(0x078, PIN_OUTPUT, 1) /* (AH37) MCAN2_RX.AUDIO_EXT_REFCLK1 */
};
&wkup_pmx2 {
- bootph-all;
wkup_uart0_pins_default: wkup-uart0-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -548,7 +546,6 @@ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
};
&wkup_pmx0 {
- bootph-all;
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -568,7 +565,6 @@ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
};
&wkup_pmx1 {
- bootph-all;
mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -740,18 +736,15 @@ &ufs_wrapper {
};
&fss {
- bootph-all;
status = "okay";
};
&ospi0 {
- bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
flash@0 {
- bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <8>;
@@ -808,13 +801,11 @@ partition@3fc0000 {
};
&ospi1 {
- bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
flash@0 {
- bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <1>;
--
2.46.0
