On 23/10/24 12:27, Manorit Chawdhry wrote:
Adding bootph properties on leaf nodes imply that they are applicable to
the parent nodes as well. Bootloaders can derive the parent nodes when
bootph is available in the leaf nodes.
Remove the bootph-* properties from parent nodes as they are redundant.
Signed-off-by: Manorit Chawdhry <m-chawdhry@xxxxxx>
Reviewed-by: Aniket Limaye <a-limaye@xxxxxx>
---
arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi | 9 ---------
1 file changed, 9 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
index 98453171a179..b2e2b9f507a9 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-j742s2-evm-common.dtsi
@@ -305,7 +305,6 @@ &wkup_gpio0 {
};
&main_pmx0 {
- bootph-all;
main_cpsw2g_default_pins: main-cpsw2g-default-pins {
pinctrl-single,pins = <
J784S4_IOPAD(0x0b8, PIN_INPUT, 6) /* (AC34) MCASP1_ACLKX.RGMII1_RD0 */
@@ -432,7 +431,6 @@ J784S4_IOPAD(0x078, PIN_OUTPUT, 1) /* (AH37) MCAN2_RX.AUDIO_EXT_REFCLK1 */
};
&wkup_pmx2 {
- bootph-all;
wkup_uart0_pins_default: wkup-uart0-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -548,7 +546,6 @@ J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 7)
};
&wkup_pmx0 {
- bootph-all;
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -568,7 +565,6 @@ J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
};
&wkup_pmx1 {
- bootph-all;
mcu_fss0_ospi0_1_pins_default: mcu-fss0-ospi0-1-default-pins {
bootph-all;
pinctrl-single,pins = <
@@ -740,18 +736,15 @@ &ufs_wrapper {
};
&fss {
- bootph-all;
status = "okay";
};
&ospi0 {
- bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi0_pins_default>, <&mcu_fss0_ospi0_1_pins_default>;
flash@0 {
- bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <8>;
@@ -808,13 +801,11 @@ partition@3fc0000 {
};
&ospi1 {
- bootph-all;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
flash@0 {
- bootph-all;
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <1>;
