In order to support multiple revisions of the qcs8300-ride board, create
a .dtsi containing the common parts and split out the ethernet bits into
the actual board file as they will change in revision 2.
Signed-off-by: Yijie Yang <quic_yijiyang@xxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/qcs8300-ride.dts | 373 +----------------------------
arch/arm64/boot/dts/qcom/qcs8300-ride.dtsi | 364 ++++++++++++++++++++++++++++
2 files changed, 377 insertions(+), 360 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
index b1c9f2cb9749..9b9922f1fcc6 100644
--- a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
+++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
@@ -5,375 +5,28 @@
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
-
-#include "qcs8300.dtsi"
+#include "qcs8300-ride.dtsi"
/ {
model = "Qualcomm Technologies, Inc. QCS8300 Ride";
compatible = "qcom,qcs8300-ride", "qcom,qcs8300";
chassis-type = "embedded";
-
- aliases {
- serial0 = &uart7;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- clocks {
- xo_board_clk: xo-board-clk {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <38400000>;
- };
-
- sleep_clk: sleep-clk {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <32000>;
- };
- };
-};
-
-&apps_rsc {
- regulators-0 {
- compatible = "qcom,pmm8654au-rpmh-regulators";
- qcom,pmic-id = "a";
-
- vreg_s4a: smps4 {
- regulator-name = "vreg_s4a";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_s9a: smps9 {
- regulator-name = "vreg_s9a";
- regulator-min-microvolt = <1352000>;
- regulator-max-microvolt = <1352000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l3a: ldo3 {
- regulator-name = "vreg_l3a";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l4a: ldo4 {
- regulator-name = "vreg_l4a";
- regulator-min-microvolt = <880000>;
- regulator-max-microvolt = <912000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l5a: ldo5 {
- regulator-name = "vreg_l5a";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l6a: ldo6 {
- regulator-name = "vreg_l6a";
- regulator-min-microvolt = <880000>;
- regulator-max-microvolt = <912000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l7a: ldo7 {
- regulator-name = "vreg_l7a";
- regulator-min-microvolt = <880000>;
- regulator-max-microvolt = <912000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l8a: ldo8 {
- regulator-name = "vreg_l8a";
- regulator-min-microvolt = <2504000>;
- regulator-max-microvolt = <2960000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l9a: ldo9 {
- regulator-name = "vreg_l9a";
- regulator-min-microvolt = <2970000>;
- regulator-max-microvolt = <3072000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
- };
-
- regulators-1 {
- compatible = "qcom,pmm8654au-rpmh-regulators";
- qcom,pmic-id = "c";
-
- vreg_s5c: smps5 {
- regulator-name = "vreg_s5c";
- regulator-min-microvolt = <1104000>;
- regulator-max-microvolt = <1104000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l1c: ldo1 {
- regulator-name = "vreg_l1c";
- regulator-min-microvolt = <300000>;
- regulator-max-microvolt = <500000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l2c: ldo2 {
- regulator-name = "vreg_l2c";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <904000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l4c: ldo4 {
- regulator-name = "vreg_l4c";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l6c: ldo6 {
- regulator-name = "vreg_l6c";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l7c: ldo7 {
- regulator-name = "vreg_l7c";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l8c: ldo8 {
- regulator-name = "vreg_l8c";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
-
- vreg_l9c: ldo9 {
- regulator-name = "vreg_l9c";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
- regulator-allow-set-load;
- regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
- RPMH_REGULATOR_MODE_HPM>;
- };
- };
};
ðernet0 {
phy-mode = "sgmii";
- phy-handle = <&sgmii_phy0>;
-
- pinctrl-0 = <ðernet0_default>;
- pinctrl-names = "default";
-
- snps,mtl-rx-config = <&mtl_rx_setup>;
- snps,mtl-tx-config = <&mtl_tx_setup>;
- snps,ps-speed = <1000>;
-
- status = "okay";
-
- mdio {
- compatible = "snps,dwmac-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
-
- sgmii_phy0: phy@8 {
- compatible = "ethernet-phy-id0141.0dd4";
- reg = <0x8>;
- device_type = "ethernet-phy";
- interrupts-extended = <&tlmm 4 IRQ_TYPE_EDGE_FALLING>;
- reset-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
- reset-assert-us = <11000>;
- reset-deassert-us = <70000>;
- };
- };
-
- mtl_rx_setup: rx-queues-config {
- snps,rx-queues-to-use = <4>;
- snps,rx-sched-sp;
-
- queue0 {
- snps,dcb-algorithm;
- snps,map-to-dma-channel = <0x0>;
- snps,route-up;
- snps,priority = <0x1>;
- };
-
- queue1 {
- snps,dcb-algorithm;
- snps,map-to-dma-channel = <0x1>;
- snps,route-ptp;
- };
-
- queue2 {
- snps,avb-algorithm;
- snps,map-to-dma-channel = <0x2>;
- snps,route-avcp;
- };
-
- queue3 {
- snps,avb-algorithm;
- snps,map-to-dma-channel = <0x3>;
- snps,priority = <0xc>;
- };
- };
-
- mtl_tx_setup: tx-queues-config {
- snps,tx-queues-to-use = <4>;
- snps,tx-sched-sp;
-
- queue0 {
- snps,dcb-algorithm;
- };
-
- queue1 {
- snps,dcb-algorithm;
- };
-
- queue2 {
- snps,avb-algorithm;
- snps,send_slope = <0x1000>;
- snps,idle_slope = <0x1000>;
- snps,high_credit = <0x3e800>;
- snps,low_credit = <0xffc18000>;
- };
-
- queue3 {
- snps,avb-algorithm;
- snps,send_slope = <0x1000>;
- snps,idle_slope = <0x1000>;
- snps,high_credit = <0x3e800>;
- snps,low_credit = <0xffc18000>;
- };
- };
-};
-
-&gcc {
- clocks = <&rpmhcc RPMH_CXO_CLK>,
- <&sleep_clk>,
- <0>,
- <0>,
- <0>,
- <0>,
- <0>,
- <0>,
- <0>,
- <0>;
-};
-
-&qupv3_id_0 {
- status = "okay";
};
-&remoteproc_adsp {
- firmware-name = "qcom/qcs8300/adsp.mbn";
- status = "okay";
-};
-
-&remoteproc_cdsp {
- firmware-name = "qcom/qcs8300/cdsp0.mbn";
- status = "okay";
-};
-
-&remoteproc_gpdsp {
- firmware-name = "qcom/qcs8300/gpdsp0.mbn";
- status = "okay";
-};
-
-&rpmhcc {
- clocks = <&xo_board_clk>;
- clock-names = "xo";
-};
-
-&serdes0 {
- phy-supply = <&vreg_l5a>;
- status = "okay";
-};
-
-&tlmm {
- ethernet0_default: ethernet0-default-state {
- ethernet0_mdc: ethernet0-mdc-pins {
- pins = "gpio5";
- function = "emac0_mdc";
- drive-strength = <16>;
- bias-pull-up;
- };
-
- ethernet0_mdio: ethernet0-mdio-pins {
- pins = "gpio6";
- function = "emac0_mdio";
- drive-strength = <16>;
- bias-pull-up;
- };
+&mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ sgmii_phy0: phy@8 {
+ compatible = "ethernet-phy-id0141.0dd4";
+ reg = <0x8>;
+ device_type = "ethernet-phy";
+ interrupts-extended = <&tlmm 4 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <11000>;
+ reset-deassert-us = <70000>;
};
};
-
-&uart7 {
- status = "okay";
-};
-
-&ufs_mem_hc {
- reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
- vcc-supply = <&vreg_l8a>;
- vcc-max-microamp = <1100000>;
- vccq-supply = <&vreg_l4c>;
- vccq-max-microamp = <1200000>;
- status = "okay";
-};
-
-&ufs_mem_phy {
- vdda-phy-supply = <&vreg_l4a>;
- vdda-pll-supply = <&vreg_l5a>;
- status = "okay";
-};
diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dtsi b/arch/arm64/boot/dts/qcom/qcs8300-ride.dtsi
new file mode 100644
index 000000000000..e6099f7d80cb
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dtsi
@@ -0,0 +1,364 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "qcs8300.dtsi"
+/ {
+ aliases {
+ serial0 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0: 115200n8";
+ };
+
+ clocks {
+ xo_board_clk: xo-board-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <38400000>;
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32000>;
+ };
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pmm8654au-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vreg_s4a: smps4 {
+ regulator-name = "vreg_s4a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s9a: smps9 {
+ regulator-name = "vreg_s9a";
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3a: ldo3 {
+ regulator-name = "vreg_l3a";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4a: ldo4 {
+ regulator-name = "vreg_l4a";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5a: ldo5 {
+ regulator-name = "vreg_l5a";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6a: ldo6 {
+ regulator-name = "vreg_l6a";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a: ldo7 {
+ regulator-name = "vreg_l7a";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8a: ldo8 {
+ regulator-name = "vreg_l8a";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9a: ldo9 {
+ regulator-name = "vreg_l9a";
+ regulator-min-microvolt = <2970000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pmm8654au-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vreg_s5c: smps5 {
+ regulator-name = "vreg_s5c";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1c: ldo1 {
+ regulator-name = "vreg_l1c";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <500000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2c: ldo2 {
+ regulator-name = "vreg_l2c";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4c: ldo4 {
+ regulator-name = "vreg_l4c";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6c: ldo6 {
+ regulator-name = "vreg_l6c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7c: ldo7 {
+ regulator-name = "vreg_l7c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8c: ldo8 {
+ regulator-name = "vreg_l8c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9c: ldo9 {
+ regulator-name = "vreg_l9c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+ðernet0 {
+ phy-handle = <&sgmii_phy0>;
+
+ pinctrl-0 = <ðernet0_default>;
+ pinctrl-names = "default";
+
+ snps,mtl-rx-config = <&mtl_rx_setup>;
+ snps,mtl-tx-config = <&mtl_tx_setup>;
+ snps,ps-speed = <1000>;
+
+ status = "okay";
+
+ mdio: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mtl_rx_setup: rx-queues-config {
+ snps,rx-queues-to-use = <4>;
+ snps,rx-sched-sp;
+
+ queue0 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x0>;
+ snps,route-up;
+ snps,priority = <0x1>;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x1>;
+ snps,route-ptp;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x2>;
+ snps,route-avcp;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x3>;
+ snps,priority = <0xc>;
+ };
+ };
+
+ mtl_tx_setup: tx-queues-config {
+ snps,tx-queues-to-use = <4>;
+ snps,tx-sched-sp;
+
+ queue0 {
+ snps,dcb-algorithm;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+ };
+};
+
+&gcc {
+ clocks = <&rpmhcc RPMH_CXO_CLK>,
+ <&sleep_clk>,
+ <0>,
+ <0>,
+ <0>,
+ <0>,
+ <0>,
+ <0>,
+ <0>,
+ <0>;
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/qcs8300/adsp.mbn";
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/qcs8300/cdsp0.mbn";
+ status = "okay";
+};
+
+&remoteproc_gpdsp {
+ firmware-name = "qcom/qcs8300/gpdsp0.mbn";
+ status = "okay";
+};
+
+&rpmhcc {
+ clocks = <&xo_board_clk>;
+ clock-names = "xo";
+};
+
+&serdes0 {
+ phy-supply = <&vreg_l5a>;
+ status = "okay";
+};
+
+&tlmm {
+ ethernet0_default: ethernet0-default-state {
+ ethernet0_mdc: ethernet0-mdc-pins {
+ pins = "gpio5";
+ function = "emac0_mdc";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+
+ ethernet0_mdio: ethernet0-mdio-pins {
+ pins = "gpio6";
+ function = "emac0_mdio";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+ };
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vreg_l8a>;
+ vcc-max-microamp = <1100000>;
+ vccq-supply = <&vreg_l4c>;
+ vccq-max-microamp = <1200000>;
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l4a>;
+ vdda-pll-supply = <&vreg_l5a>;
+ status = "okay";
+};
+
+&uart7 {
+ status = "okay";
+};
--
2.34.1
