Zyxel EX3510-B is a WiFi 6 capable home gateway (family) based on the
BCM4906 SoC, with 512MiB of RAM and 512MiB of NAND flash. WiFi support
consists of a BCM6710 and a BCM6715 attached to separate PCIe buses.
Add an initial devicetree for this system, with support for:
- Onboard UART (per base dtsi)
- USB (2.0 only; superspeed devices are treated as high-speed due to an
unknown cause)
- Both buttons (rear reset, front WPS)
- Almost all LEDs:
- Power (red/green)
- Internet (red/green)
- WAN (green)
- LAN (green; anode is connected to GPIO 13 so currently
nonfunctioning)
- USB (green)
- WPS button (red/green)
- Absent in DT: There are 2.4GHz/5.0GHz WiFi status LEDs connected to
the WiFi chips instead of the SoC.
- NAND flash
- Embedded Ethernet switch
- Factory-programmed Ethernet MAC address
WiFi cannot be enabled at this time due to Linux lacking drivers for
both the PCIe controllers and the PCIe WiFi peripherals.
Signed-off-by: Sam Edwards <CFSworks@xxxxxxxxx>
---
arch/arm64/boot/dts/broadcom/bcmbca/Makefile | 1 +
.../broadcom/bcmbca/bcm4906-zyxel-ex3510b.dts | 196 ++++++++++++++++++
2 files changed, 197 insertions(+)
create mode 100644 arch/arm64/boot/dts/broadcom/bcmbca/bcm4906-zyxel-ex3510b.dts
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/Makefile b/arch/arm64/boot/dts/broadcom/bcmbca/Makefile
index 27741b71ba9e..9a8461d91c8c 100644
--- a/arch/arm64/boot/dts/broadcom/bcmbca/Makefile
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/Makefile
@@ -2,6 +2,7 @@
dtb-$(CONFIG_ARCH_BCMBCA) += \
bcm4906-netgear-r8000p.dtb \
bcm4906-tplink-archer-c2300-v1.dtb \
+ bcm4906-zyxel-ex3510b.dtb \
bcm4908-asus-gt-ac5300.dtb \
bcm4908-netgear-raxe500.dtb \
bcm94908.dtb \
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906-zyxel-ex3510b.dts b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906-zyxel-ex3510b.dts
new file mode 100644
index 000000000000..54e453bd09f7
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906-zyxel-ex3510b.dts
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "bcm4906.dtsi"
+
+/ {
+ compatible = "zyxel,ex3510b", "brcm,bcm4906", "brcm,bcm4908", "brcm,bcmbca";
+ model = "Zyxel EX3510-B";
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x20000000>;
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ poll-interval = <100>;
+
+ key-wps {
+ label = "WPS";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
+ };
+
+ key-reset {
+ label = "Reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&leds {
+ pinctrl-0 = <&pins_led_0_a>, <&pins_led_2_a>, <&pins_led_3_a>,
+ <&pins_led_4_a>, <&pins_led_10_a>, <&pins_led_12_a>,
+ <&pins_led_14_a>, <&pins_led_15_a>, <&pins_led_21_a>;
+ pinctrl-names = "default";
+
+ led@0 {
+ reg = <0x0>;
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led@2 {
+ reg = <0x2>;
+ function = LED_FUNCTION_WAN_ONLINE;
+ color = <LED_COLOR_ID_GREEN>;
+ };
+
+ led@3 {
+ reg = <0x3>;
+ function = LED_FUNCTION_WAN_ONLINE;
+ color = <LED_COLOR_ID_RED>;
+ };
+
+ led@4 {
+ reg = <0x4>;
+ function = LED_FUNCTION_USB;
+ color = <LED_COLOR_ID_GREEN>;
+ trigger-sources = <&ohci_port1>, <&ohci_port2>,
+ <&ehci_port1>, <&ehci_port2>,
+ <&xhci_port1>, <&xhci_port2>;
+ linux,default-trigger = "usbport";
+ };
+
+ led@a {
+ reg = <0xa>;
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_GREEN>;
+ linux,default-trigger = "default-on";
+ };
+
+ led@c {
+ reg = <0xc>;
+ function = LED_FUNCTION_LAN;
+ color = <LED_COLOR_ID_GREEN>;
+ active-low;
+ };
+
+ led@e {
+ reg = <0xe>;
+ function = LED_FUNCTION_WPS;
+ color = <LED_COLOR_ID_GREEN>;
+ active-low;
+ };
+
+ led@f {
+ reg = <0xf>;
+ function = LED_FUNCTION_WPS;
+ color = <LED_COLOR_ID_RED>;
+ active-low;
+ };
+
+ led@15 {
+ reg = <0x15>;
+ function = LED_FUNCTION_WAN;
+ color = <LED_COLOR_ID_GREEN>;
+ active-low;
+ };
+};
+
+&enet {
+ nvmem-cells = <&base_mac_addr>;
+ nvmem-cell-names = "mac-address";
+};
+
+&usb_phy {
+ brcm,ioc = <1>;
+ brcm,ipp = <1>;
+ status = "okay";
+};
+
+&ehci {
+ status = "okay";
+};
+
+&ohci {
+ status = "okay";
+};
+
+&xhci {
+ status = "okay";
+};
+
+&ports {
+ port@0 {
+ label = "lan1";
+ };
+
+ port@1 {
+ label = "lan2";
+ };
+
+ port@2 {
+ label = "lan3";
+ };
+
+ port@3 {
+ label = "lan4";
+ };
+
+ port@7 {
+ reg = <7>;
+ phy-mode = "internal";
+ phy-handle = <&phy12>;
+ label = "wan";
+ };
+};
+
+&nand_controller {
+ status = "okay";
+};
+
+&nandcs {
+ brcm,nand-oob-sector-size = <27>;
+ nand-ecc-strength = <8>;
+ nand-ecc-step-size = <512>;
+ nand-on-flash-bbt;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ partitions {
+ compatible = "brcm,bcm4908-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ compatible = "nvmem-cells";
+ label = "cferom";
+ reg = <0x0 0x100000>;
+ read-only;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ base_mac_addr: mac@106a0 {
+ reg = <0x106a0 0x6>;
+ };
+ };
+
+ partition@100000 {
+ compatible = "brcm,bcm4908-firmware";
+ reg = <0x100000 0x5f80000>;
+ };
+
+ partition@6080000 {
+ compatible = "brcm,bcm4908-firmware";
+ reg = <0x6080000 0x5f80000>;
+ };
+ };
+};
--
2.44.2
