On Thu, Mar 19, 2015 at 09:19:16AM +0800, Peter Chen wrote:
> It is used to configure controller parameters according to
> platform data, like speed, interrupt threshold, stream mode, etc.
>
> Signed-off-by: Peter Chen <peter.chen@xxxxxxxxxxxxx>
> ---
> drivers/usb/chipidea/ci.h | 2 ++
> drivers/usb/chipidea/core.c | 57 +++++++++++++++++++++++++++++++--------------
> drivers/usb/chipidea/host.c | 6 +----
> 3 files changed, 43 insertions(+), 22 deletions(-)
>
> diff --git a/drivers/usb/chipidea/ci.h b/drivers/usb/chipidea/ci.h
> index aeec5f0..888606b 100644
> --- a/drivers/usb/chipidea/ci.h
> +++ b/drivers/usb/chipidea/ci.h
> @@ -426,4 +426,6 @@ u8 hw_port_test_get(struct ci_hdrc *ci);
> int hw_wait_reg(struct ci_hdrc *ci, enum ci_hw_regs reg, u32 mask,
> u32 value, unsigned int timeout_ms);
>
> +void ci_platform_config(struct ci_hdrc *ci, int usb_mode);
> +
> #endif /* __DRIVERS_USB_CHIPIDEA_CI_H */
> diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
> index 4d79392..f713e32 100644
> --- a/drivers/usb/chipidea/core.c
> +++ b/drivers/usb/chipidea/core.c
> @@ -403,6 +403,44 @@ static int ci_usb_phy_init(struct ci_hdrc *ci)
> return ret;
> }
>
> +
> +/**
> + * ci_platform_config: do controller configure
> + * @ci: the controller
> + * @usb_mode: the usb mode
> + *
> + */
> +void ci_platform_config(struct ci_hdrc *ci, int usb_mode)
> +{
> + if (usb_mode == USBMODE_CM_DC) {
> + if (ci->platdata->flags & CI_HDRC_DISABLE_DEVICE_STREAMING)
> + hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS,
> + USBMODE_CI_SDIS);
> +
> + /*
> + * Set interrupt interval for device mode
> + * host set ITC according to ehci-hcd module
> + * parameter log2_irq_thresh
> + */
> + hw_write(ci, OP_USBCMD, 0xff0000,
> + ci->platdata->gadget_itc_setting << 16);
> + } else if (usb_mode == USBMODE_CM_HC) {
> + if (ci->platdata->flags & CI_HDRC_DISABLE_HOST_STREAMING)
> + hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS,
> + USBMODE_CI_SDIS);
> + } else {
> + dev_warn(ci->dev, "USB mode in still not set\n");
> + }
> +
> + if (ci->platdata->flags & CI_HDRC_FORCE_FULLSPEED) {
> + if (ci->hw_bank.lpm)
> + hw_write(ci, OP_DEVLC, DEVLC_PFSC, DEVLC_PFSC);
> + else
> + hw_write(ci, OP_PORTSC, PORTSC_PFSC, PORTSC_PFSC);
> + }
> +
> +}
> +
> /**
> * hw_controller_reset: do controller reset
> * @ci: the controller
> @@ -447,35 +485,20 @@ int hw_device_reset(struct ci_hdrc *ci)
> ci->platdata->notify_event(ci,
> CI_HDRC_CONTROLLER_RESET_EVENT);
>
> - if (ci->platdata->flags & CI_HDRC_DISABLE_DEVICE_STREAMING)
> - hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS, USBMODE_CI_SDIS);
> -
> - if (ci->platdata->flags & CI_HDRC_FORCE_FULLSPEED) {
> - if (ci->hw_bank.lpm)
> - hw_write(ci, OP_DEVLC, DEVLC_PFSC, DEVLC_PFSC);
> - else
> - hw_write(ci, OP_PORTSC, PORTSC_PFSC, PORTSC_PFSC);
> - }
> -
> /* USBMODE should be configured step by step */
> hw_write(ci, OP_USBMODE, USBMODE_CM, USBMODE_CM_IDLE);
> hw_write(ci, OP_USBMODE, USBMODE_CM, USBMODE_CM_DC);
> /* HW >= 2.3 */
> hw_write(ci, OP_USBMODE, USBMODE_SLOM, USBMODE_SLOM);
>
> - /*
> - * Set interrupt interval for device mode
> - * host set ITC according to ehci-hcd module parameter log2_irq_thresh
> - */
> - hw_write(ci, OP_USBCMD, 0xff0000,
> - ci->platdata->gadget_itc_setting << 16);
> -
This codepath was added by patch 02 "usb: chipidea: set ITC to 0 for
device mode". You should add it after this one, so this code gets added
directly to its final position.
> if (hw_read(ci, OP_USBMODE, USBMODE_CM) != USBMODE_CM_DC) {
> pr_err("cannot enter in %s device mode", ci_role(ci)->name);
> pr_err("lpm = %i", ci->hw_bank.lpm);
> return -ENODEV;
> }
>
> + ci_platform_config(ci, USBMODE_CM_DC);
> +
> return 0;
> }
>
> diff --git a/drivers/usb/chipidea/host.c b/drivers/usb/chipidea/host.c
> index b262c1c..c4f76b7 100644
> --- a/drivers/usb/chipidea/host.c
> +++ b/drivers/usb/chipidea/host.c
> @@ -141,11 +141,7 @@ static int host_start(struct ci_hdrc *ci)
> }
> }
>
> - if (ci->platdata->flags & CI_HDRC_FORCE_FULLSPEED)
> - hw_write(ci, OP_PORTSC, PORTSC_PFSC, PORTSC_PFSC);
> -
> - if (ci->platdata->flags & CI_HDRC_DISABLE_HOST_STREAMING)
> - hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS, USBMODE_CI_SDIS);
> + ci_platform_config(ci, USBMODE_CM_HC);
>
> return ret;
>
> --
> 1.9.1
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-usb" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
